Jensen VM9020TS operation manual Operating Instructions

[RESET] Button

VM9020TS

OPERATING INSTRUCTIONS

Power On / Off

Press the /MUTE button (1) to turn the unit on. The buttons on the front of the unit will light up.

Press and hold the /MUTE button (1) on the front panel or the POWER button (4) on the remote to power off the unit.

Audible Beep Confirmation

An audible beep tone confirms each function selection. The beep tone cannot be disabled.

Mute

Press the /MUTE button (1) on the front panel or remote (3) to mute the volume from the unit. Press the MUTE button again to restore the volume. The mute icon flashes on the right side of the screen. Adjusting the volume or using any of the audio set-up features cancels the mute function.

Playing Source Selection

Press the SRC button (11) on the remote to change between available playing sources in the following order: TUNER, DVD, AUX IN or CAMERA (rear view video camera). The playing mode is displayed on the screen.

Press the MENU/SRC button (11) on the unit to access the playing source menu. Use the direction buttons on the joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to

select a playing source, then press the button (18) or the joystick enter button (5) to enter the selected source.

AUX IN Mode

An external peripheral device can be connected to this unit via RCA output and “AUX-IN”.

CAMERA Mode

“CAMERA” mode is only available if the camera is connected and during reverse driving. To install a rear view video camera, connect the video input cable to the camera output cable.

Volume Adjustment

To increase the volume level, press the VOL + button (3) on the front panel or remote control. To decrease the volume level, press the VOL - button (4) on the front panel or remote control.The volume ranges from “0” to “40”. When the volume level reaches “0” or “40”, a triple beep sounds, indicating that the adjustment limit has been reached. The screen displays the volume level for 3 seconds.

Programmable Turn-On Volume

This feature allows the user to select a turn-on volume setting regardless of the volume setting prior to turning the unit off.

To program a specific volume level, push and hold the AUDIO button (2) while the yellow volume bar is displayed on the screen. The unit will beep two times to confirm your turn- on volume setting.

Audio Control Menu

The Audio Control feature allows you to easily adjust your audio system to meet the acoustical characteristics of your vehicle, which vary depending on the type of vehicle and its measurements. To get the best possible sound quality from your new system, be sure to adjust the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects of the cabin equalizer.

Accessing the Audio Control Menu

Press the AUDIO/LOC button (2) on the front panel to display the “AUDIO” menu.

Selecting an Audio Feature for Adjustment

Press the ( )/( ) buttons (8, 9) on the joystick or the ()/

( ) buttons (17, 19) on the remote control to select the audio feature to be adjusted.

Adjusting an Audio Feature

Press the or buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to adjust the selected feature to the desired setting.

Table 4: Audio Adjustments

Audio Function	Adjustable Range
EQ	User
	Flat
	Jazz
	Pop
	Classical
	Rock
	Vocal
Bass	-14 to +14
Treble	-14 to +14
Fade	-9 to +9
Bal	-9 to +9
SW	-7 to +7
Loud	Off, 1-4

NOTE: The Bass and Treble levels are only adjustable when EQ is set to “User” mode.

The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or “off”. When the Loud function is on, LOUD is displayed on the screen.

Exiting the Audio Control Menu

Press and hold the AUDIO/LOC button (2) or stop making adjustments for a few seconds to exit the audio control menu.

Six-Channel Audio Control

NOTE: Before adjusting the volume of any speaker, please refer to “Surround Setup” on page 18.

Table 5: 6-Channel Audio Adjustments

Item	Adjustable Range
Master Volume	00 to 40
Front Left Channel Volume	-10 to +10
Front Right Channel Volume	-10 to +10
Rear Left Channel Volume	-10 to +10
Rear Right Channel Volume	-10 to +10
Center Channel Volume	-10 to +10
Subwoofer Volume	-10 to +10

Rear Zone

If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in the back seat can control the DVD output using the rear zone remote control. See “Multi-Zone Remote Control” on page 8 for instructions.

System Reset

To correct a system halt or other illegal operation, use the tip of a pen to press the RESET button (25) located on the

front bottom-left corner of the TFT screen. After a system reset, the unit restores all factory default settings.

NOTE: If the unit is reset while a DVD is playing, the DVD resumes play once the reset is complete.

Line Mute

If the “MUTE” wire is connected, audio output mutes when a telephone call is received by the car phone or when verbal navigation is performed. See “Wiring” on page 3.

10