Manuals / Jet Tools / Power Tools / Saw

Jet Tools JWCS-10 owner manual Rail Installation on a non-JET Table Saw

Models: JWCS-10

1 16
Download 16 pages 33.79 Kb
Page 12
Image 12

90° to the Table Adjustment

1.Place the fence on the saw table and lock it.

2.Place a square (A, Fig. 17) on the table next to the fence. The fence should be 90° to the table.

3.If adjustment is necessary, unlock the fence, and turn one of the two nylon adjustment screws (B, Fig. 17) until the fence is 90° to the table.

4.Lock the fence and check the adjustment again.

Cursor Adjustment

1.Disconnect the table saw from the power source.

2.Raise the saw blade above the tabletop.

3.Unlock the fence and slide it to approximately four inches from the saw blade.

4.Lock the fence.

5.Measure the distance between the saw blade and the inside of the fence.

6.Adjust the cursor (C, Fig. 17) to read the distance just measured and tighten the cursor assembly to the fence.

7.Take a test cut and confirm that the adjustment is correct.

Note: If the cursor does not have enough travel to give the correct measurement loosen the guide rail and adjust as needed. If you still do not get the correct measurement loosen the front rail and adjust as needed. If you have to adjust the front rail you will need to go through the front rail assembly instructions again.

This adjustment must be checked whenever a different blade is installed.

After installing the XACTA Fence II press the black plastic end caps into the openings of the guide rail. There is also an end cap for the fence, but this should already be installed.

Figure 17

Rail Installation on a non-JET Table Saw

The XACTA Fence II Homeshop 30/52 Fence and Rail System can be installed on a non-JET table saw. Instructions for the rail and fence installation as well as the optional extension table are provided in Manual No. M-2195075EZ and is available on- line or a copy can be obtained by contacting customer service.

Trouble-Shooting for XACTA Fence II Homeshop 30/52

Problem

Possible Cause

Solution

Lock lever won't go down, or

Too much pressure against

Back out set screws.

requires excessive force.

guide tube.

 

Fence scrapes table, won't slide

Fence height not adjusted

Adjust nylon screws.

smoothly.

properly.

 

Fence "hangs" or binds while

Front rail not level.

Readjust rail.

sliding.

 

 

12

Page 11 Page 13
Page 12
Image 12
Jet Tools JWCS-10 owner manual Rail Installation on a non-JET Table Saw, Trouble-Shooting for Xacta Fence II Homeshop 30/52
Page 11 Page 13

JWCS-10 specifications

The Jet Tools JWCS-10 is a powerful and versatile woodcutting solution designed primarily for woodworkers and DIY enthusiasts. This table saw is specifically engineered to provide precise cuts with exceptional accuracy, making it an essential tool for both professional workshops and home garages.

One of the standout features of the JWCS-10 is its heavy-duty construction, built to withstand substantial wear and tear over time. The table saw incorporates a robust cast iron table that provides a stable surface for cutting. This solid base not only enhances stability but also minimizes vibration during operation, resulting in smoother cuts and improved overall performance.

Equipped with a 15-amp motor, the JWCS-10 delivers impressive power, allowing it to tackle even the toughest hardwoods with ease. The motor can achieve a maximum RPM of 4,800, providing the necessary speed for a variety of cutting applications. The saw blade can be easily adjusted to various angles, accommodating both beveled and miter cuts. This versatility expands the range of carpentry projects that can be completed with precision.

The JWCS-10 also features a large rip capacity, capable of handling wide boards. The rip fence is easily adjustable and locks securely, offering enhanced accuracy for repetitive cuts. Additionally, the table saw includes a built-in splitter and anti-kickback pawls, essential safety features that minimize the risk of kickback during operation.

Another notable technological aspect of the JWCS-10 is its dust collection system. It incorporates a 2-1/2 inch dust port that connects to standard shop vacuums, ensuring a cleaner workspace and improved visibility while cutting. This is especially important for woodworkers who need to maintain a tidy environment and reduce potential hazards from sawdust accumulation.

Furthermore, the JWCS-10 boasts user-friendly features that enhance the overall cutting experience. A clear blade guard allows for maximum visibility while also providing necessary safety protection. The inclusion of a push stick ensures that users can maintain a safe distance from the blade during operation.

In summary, the Jet Tools JWCS-10 is engineered for durability, precision, and safety. With its powerful motor, extensive cutting capacity, and thoughtful design features, it is an excellent investment for anyone serious about woodworking. Whether you are a seasoned pro or a hobbyist, the JWCS-10 will help you tackle a wide range of projects with confidence and ease.