Back Rail Installation

1.Locate the back rail which is 1-1/2" x 1-1/2" with holes running along one side only. The height of the back rail when attached to the saw is not critical.

2.Align the holes in the back rail to the holes in the table top, as shown in Figure 4.

3.Secure the back rail to the holes in the saw table with four 1/4-20x 1-1/2 hex cap screws, eight 1/4 flat washers, four 1/4 lock washers, and four 1/4 hex nuts as shown in Figure 5.

Tighten screws securely with two 10mm

Figure 4

wrenches.

 

Note: If you are installing an optional wood

 

extension table on your saw, it should be installed

 

first before mounting the guide tube. This will

 

prevent having to mount and align the guide tube

 

twice.

 

If you are not mounting an optional wood table,

 

skip the following section and proceed to Guide

 

Tube section.

 

Wooden Extension Table

The wooden extension table is an optional accessory.

Tools required

Figure 5

Electric drill

 

Cross point screwdriver

 

10mm open end wrenches

 

Four clamps

 

Straight edge

 

Hammer (or rubber mallet)

 

Installation

The optional wood extension table (including the optional router table) sits flush against the saw table and along the inside of the rails. The Warning label on the router table should face outward. The extension table is not bolted to the saw table; it is bolted only to the rails.

The extension table and saw table must be aligned properly so the XACTA Fence II will slide smoothly from one to the other.

1.Place the extension table between the rails and up against the saw table, leaving the extension table raised just slightly above the saw table.

Clamp the extension table to the front and back rails as shown in Figure 6. Clamping pressure should be enough to secure the table yet allow minor adjustments.

Figure 6

2.Use a hammer and block of wood (or a rubber mallet) to tap the extension table up flush against the cast iron saw table (Figure 6).

8

Page 7 Page 9
Page 8
Image 8
Jet Tools JWCS-10 owner manual Wooden Extension Table, Back Rail Installation
Page 7 Page 9

JWCS-10 specifications

The Jet Tools JWCS-10 is a powerful and versatile woodcutting solution designed primarily for woodworkers and DIY enthusiasts. This table saw is specifically engineered to provide precise cuts with exceptional accuracy, making it an essential tool for both professional workshops and home garages.

One of the standout features of the JWCS-10 is its heavy-duty construction, built to withstand substantial wear and tear over time. The table saw incorporates a robust cast iron table that provides a stable surface for cutting. This solid base not only enhances stability but also minimizes vibration during operation, resulting in smoother cuts and improved overall performance.

Equipped with a 15-amp motor, the JWCS-10 delivers impressive power, allowing it to tackle even the toughest hardwoods with ease. The motor can achieve a maximum RPM of 4,800, providing the necessary speed for a variety of cutting applications. The saw blade can be easily adjusted to various angles, accommodating both beveled and miter cuts. This versatility expands the range of carpentry projects that can be completed with precision.

The JWCS-10 also features a large rip capacity, capable of handling wide boards. The rip fence is easily adjustable and locks securely, offering enhanced accuracy for repetitive cuts. Additionally, the table saw includes a built-in splitter and anti-kickback pawls, essential safety features that minimize the risk of kickback during operation.

Another notable technological aspect of the JWCS-10 is its dust collection system. It incorporates a 2-1/2 inch dust port that connects to standard shop vacuums, ensuring a cleaner workspace and improved visibility while cutting. This is especially important for woodworkers who need to maintain a tidy environment and reduce potential hazards from sawdust accumulation.

Furthermore, the JWCS-10 boasts user-friendly features that enhance the overall cutting experience. A clear blade guard allows for maximum visibility while also providing necessary safety protection. The inclusion of a push stick ensures that users can maintain a safe distance from the blade during operation.

In summary, the Jet Tools JWCS-10 is engineered for durability, precision, and safety. With its powerful motor, extensive cutting capacity, and thoughtful design features, it is an excellent investment for anyone serious about woodworking. Whether you are a seasoned pro or a hobbyist, the JWCS-10 will help you tackle a wide range of projects with confidence and ease.
Top Page Image Contents