JL Audio A2150 owner manual Protect Your Hearing, Serial Number, Installation Applications

PROTECT YOUR HEARING!

We value you as a long-term customer. For that reason, we urge you to practice restraint in the operation of this product so as not to damage your hearing and that of others in your vehicle. Studies have shown that continuous exposure to high sound pressure levels can lead to permanent (irreparable) hearing loss. This and all other high-power amplifiers are capable of producing such high sound pressure levels when connected to a speaker system. Please limit your continuous exposure to high volume levels.

While driving, operate your audio system in a manner that still allows you to hear necessary noises to operate your vehicle safely (horns, sirens, etc.).

SERIAL NUMBER

In the event that your amplifier requires service or is ever stolen, you will need to have a record of the product’s serial number. Please take the time to enter that number in the space provided below. The serial number can be found on the bottom panel of the amplifier and on the amplifier packaging.

Serial Number:

INSTALLATION APPLICATIONS

This amplifier is designed for operation in vehicles with 12 volt, negative-ground electrical systems. Use of this product in vehicles with positive ground and/or voltages other than 12V may result in damage to the product and will void the warranty.

This product is not certified or approved for use in aircraft.

Do not attempt to “bridge” the outputs of this amplifier with the outputs of a second amplifier, including an identical one.

Chassis Ground

Connector

(pg. 5)

+12 V Power	Remote Turn-On
Connector	Connector
(pg. 5)	(pg. 6)

PLANNING YOUR INSTALLATION

It is important that you take the time to read this manual and that you plan out your installation carefully. The following are some considerations that you must take into account when planning your installation.

Cooling Efficiency Considerations:

The outer shell of your JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling performance, this outer shell should be exposed to as large a volume of air as possible. Enclosing the amplifier in a small, poorly ventilated chamber can

lead to excessive heat build-up and degraded performance. If an installation calls for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the aid of a fan. In normal applications, fan-cooling is not necessary.

Speaker Outputs

(pg. 8)

Mounting the amplifier upside down is strongly discouraged.

If mounting the amplifier under a seat, make sure there is at least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit proper cooling.

Safety Considerations:

Your amplifier needs to be installed in a dry, well-ventilated environment and in a manner which does not interfere with your vehicle’s safety equipment (air bags, seat belt systems, ABS brake systems, etc.). You should also take the time to securely mount the amplifier using the supplied screws so that it does not come loose in the event of a collision or a sudden jolt to the vehicle.

Stupid Mistakes to Avoid

• Check before drilling any holes in your vehicle

to make sure that you will not be drilling

through a gas tank, brake line, wiring harness or

other vital vehicle system.

• Do not run system wiring outside or underneath

the vehicle. This is an extremely dangerous

practice which can result in severe damage to

your vehicle and person.

• Protect all system wires from sharp metal

edges and wear by carefully routing them,

tying them down and using grommets and

Input Voltage

Left & Right

Protection Status

Bass EQ

Filter Mode

Selection

Preamp Output Jacks

Indicator

On/Off Switch

Selection

(pg. 6)

(pg. 8)

(pg. 9)

Jack for

(pg. 8)

(pg. 7)

Left & Right

Power Status

Remote Bass

Input Sensitivity

Filter

Preamp Input Jacks

Indicator

Control Knob

Control

Frequency Selector

(pg. 6)

(pg. 9)

(pg. 8)

(pg. 6)

(pg. 7)

loom where appropriate.

• Do not mount the amplifier in the engine

compartment, under the vehicle, on the roof

or in any other area that will expose the

amplifier circuitry to the elements.

2 JL AUDIO A2150 JL AUDIO A2150 3