![](/images/new-backgrounds/1144039/14403919x1.webp)
10W7-3
Free Air Resonance (Fs): 30.6 Hz
Electrical “Q” (Qes): 0.578
Mechanical “Q” (Qms): 7.647
Total Speaker “Q” (Qts): 0.537
Equivalent Compliance (Vas): 1.28 cu. ft. (36.1 ltrs)
Thermal Power Handling (Pt): 750 Watts Continuous
Reference Efficiency (no): 0.171 %
Efficiency (SPL @ 1W/1m): 84.3 dB
DC Resistance (Re): 2.75Ω
Effective Piston Area (Sd): 59.8 sq. in. (0.0386 sq. m)
Nominal Impedance (Znom): 3Ω
* Xmax specifications are derived via
Recommended Continuous (RMS) Power Range for One Subwoofer Driver:
2 5 0 W | 5 0 0 W | 7 5 0 W | 1 0 0 0 W | 2 0 0 0 W | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Amplifier Recommendation: 500/1v2 (pictured), HD750/1
or G-MAX
JL Audio 500/1v2:
These settings are intended as a “baseline” for tuning your system. Depending on your vehicle and your preferences, some variation in the crossover and bass control settings may be necessary for optimum performance.
Bass EQ:
Generally not necessary in W7 applications (we recommend defeating it by switching the “Bass EQ” switch to “Off”). May be used with Remote Bass Control to provide some user controllable broad bass boost. When used in this manner, set “Q” to “1.1”, set “Center Freq.” to “45” Hz, “Boost” is defeated by connection of Remote Bass Control.
|
|
|
|
|
|
|
|
|
| Input Sensitivity Controls: | ||||||||
|
|
|
|
|
|
|
|
|
| |||||||||
Infrasonic Filter: |
|
| Proper adjustment of these controls is critical! | |||||||||||||||
|
| For virtually all aftermarket head units, | ||||||||||||||||
Turn “Off”for Sealed Enclosure. |
|
| set “Input Voltage” to “Low”. | |||||||||||||||
Turn “On” for Ported Enclosure and |
|
| See “Input Sensitivity Setting Guide” | |||||||||||||||
set the knob to “25” Hz. |
|
| on pg. 14 for precise setting instructions. | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dual Mono Speaker
Output Connections: Connect wire directly to “+” and
=position of knob
=position of switch
=switch with two possible positions
=setting will vary (see sidebar)
Remote Bass Port: Permits connection of an optional remote bass boost controller
Amp Low-Pass Filter:
Set “Mode/Slope” switch to “24dB”. Set “Filter Freq. (Hz)” knob to “85”. Lower settings are likely to result in a poor transition between the upper response of the W7 and the lower response of the
Amplier Input: Connect
Use both jacks (with a
10