Something not working
Please carry out the following checks before contacting your local Service Force agent.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
During machine operation it is possible that the red Start/Pause pilot light flashes, one of the following alarm codes appears on the display and some acoustic signals sound to indicate that the machine is not working:
-E10 : problem with the water supply
-E20 : problem with water draining
-E40 : door open
Once the problem has been eliminated, press the “Start/Pause” button to restart the programme. If after all checks, the problem persists, contact your local Service Force Centre.
| Symptom |
| Solution |
| |
|
|
| |||
| The machine does not start |
| ● | The door has not been closed. (E40 ) |
|
|
|
| ● | The plug is not properly inserted in the power socket. |
|
|
|
| ● | There is no supply at the socket. |
|
|
|
| ● | The main fuse or the fuse in the plug has blown. |
|
|
|
| ● | The «Start/Pause» button has not been pressed. |
|
|
|
| ● | The «Delay start» option has been selected. |
|
|
|
| ● | The «Child lock» option has been enabled. |
|
|
|
|
|
|
|
| The machine does not fill |
| ● | The water tap is closed. (E10 ) |
|
|
|
| ● | The filter in the inlet hose is blocked. (E10 ) |
|
|
|
| ● | The inlet hose may be squashed or kinked. (E10 ) |
|
|
|
| ● | The door has not been closed. (E40 ) |
|
|
|
|
|
|
|
| The machine fills then empties |
| ● | The end of the drain hose is too low. |
|
| immediately |
| ● | The end of the drain hose is submerged in water. |
|
|
|
| ● | There is no vent in the end of the drain hose. |
|
|
|
|
|
|
|
| The machine does not empty |
| ● | The drain hose may be squashed or kinked. (E20) |
|
| and/or does not spin |
| ● | The “Rinse Hold” or “Quiet” option has been selected. |
|
|
|
| ● | The drain pump may be blocked. (E20) |
|
|
|
| ● | The “No Spin” option has been selected |
|
|
|
| ● | The drainage system pipes are blocked. |
|
|
|
| ● | The programme “Soak”, which ends with water left in the tub, has |
|
| There is water on the floor |
|
| been selected . |
|
|
| ● | Too much detergent or unsuitable detergent has been used (creates |
| |
|
|
|
| too much foam). |
|
|
|
| ● | Check whether there are any leaks from the inlet hose fittings. It is not |
|
|
|
|
| always easy to see this as the water runs down the hose; check to see |
|
|
|
|
| if it is damp. |
|
|
|
| ● | The drain hose may be damaged or not securely positioned. |
|
|
|
| ● | The cap on the emergency emptying hose has not been replaced after |
|
|
|
|
| cleaning the filter. |
|
|
|
|
|
|
|
| Unsatisfactory washing results |
| ● | Too little detergent or unsuitable detergent has been used. An |
|
|
|
|
| insufficient amount of detergent leaves the laundry looking grey and |
|
|
|
|
| causes lime scale to form. |
|
|
|
| ● | Stubborn stains have not been treated prior to washing |
|
|
|
| ● | The correct wash programme/temperature has not been selected. |
|
|
|
| ● | Too much laundry has been placed in the drum. |
|
|
|
|
|
|
|
| The green Start/Pause light |
| ● | The energy save system is enabled. Press the Start/Pause button to |
|
| flashes and the display seems off |
|
| switch the appliance on. |
|
|
|
|
|
|
|
26
