FUEL HANDLING

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Always ensure there is adequate

!ventilation when handling fuel.

Gasoline

•This engine is certified to operate on unleaded gasoline.

•Use good quality unleaded gasoline.

•The lowest octane recommended is 87. If you run the engine on a lower octane than 87 it can result in knocking. This gives rise to a high engine temperature, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Two-stroke oil

•For the best results and performance use JONSERED two-stroke oil, which is specially formulated for our two- stroke engines. Mixture 1:50 (2%).

•Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

•Never use oil intended for four-stroke engines.

Gasoline,

Two-stroke

oil, litre

litre

2% (1:50)

 

5

0,10

10

0,20

15

0,30

20

0,40

US gallon

US fl. oz.

1

2 1/2

2 1/2

6 1/2

5

12 7/8

Mixing

•Always mix the gasoline and oil in a clean container intended for fuel.

•Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

•This engine is certified to operate on unleaded gasoline.

Chain oil

•The chain lubrication system is automatic and we recommend the use of special oil (chain oil) with good adhesion characteristics.

•In countries where no special chain oil is available, EP90 transmission oil can be used.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

•In temperatures below 0° C (32° F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components.

•Contact your service agent when choosing chain oil.

English – 25

Page 24 Page 26
Page 25
Image 25
Jonsered CS 2145 EPA II, CS 2150 EPA I, CS 2141 EPA II manual Fuel Handling, Chain oil
Page 24 Page 26

CS 2141 EPA II, CS 2145 EPA II, CS 2150 EPA I specifications

The Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II are premium chainsaws engineered for both professional users and serious enthusiasts. These models exemplify Jonsered's commitment to power, efficiency, and user-friendly design, making them ideal for a variety of cutting tasks, from felling trees to trimming branches.

The Jonsered CS 2150 EPA I is a robust chainsaw that offers a powerful engine combined with advanced features. It boasts a 50.2 cc engine that delivers exceptional cutting performance while adhering to strict EPA emissions standards. The chainsaw is equipped with the X-Torq engine technology, which significantly reduces fuel consumption and emissions, enabling users to work longer while minimizing environmental impact. Additionally, the CS 2150 features a high chain speed of 22.3 m/s, allowing for swift and clean cuts.

The CS 2145 EPA II further enhances performance with its lightweight design, making it easy to maneuver for prolonged use without fatigue. Powered by a 45.7 cc engine, it combines efficiency with raw power, providing reliable performance for both professionals and homeowners. The inclusion of an easy-start system means that users can start the saw with minimal effort, which is especially advantageous during colder weather or when working in challenging environments. Its validated safety features, including a chain brake and low kickback bar, ensure user protection during operation.

The CS 2141 EPA II offers a perfect balance of power and manageability. With a smaller 40.9 cc engine, it is particularly suited for users looking for an efficient saw that doesn't compromise on performance. The lightweight design allows for easy handling, particularly in dense and difficult terrain. Like the other models, it utilizes the X-Torq engine technology, which ensures reduced emissions and optimal fuel efficiency. Its precise design and ergonomic handle make it comfortable for extended periods of use, catering to both professional loggers and landscape maintenance users.

Each of these models shares characteristics such as an efficient air filtration system, which prolongs engine life by keeping dirt and debris out. In addition, they are designed with vibrations dampening technology, reducing fatigue for the user. The easy access to the filter and spark plug simplifies maintenance, ensuring the chainsaws remain in peak condition.

In conclusion, the Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II represent a solid lineup of chainsaws that combine power, efficiency, and safety. With advanced technologies and thoughtful design, they cater to a wide range of cutting needs, making them indispensable tools for anyone serious about their work in forestry, landscaping, or yard maintenance.
Top Page Image Contents