Starter, Correctly adjusted carburettor

MAINTENANCE

“whistles“ the setting is too lean. If there is too much exhaust gas at the same time as the machine “4-cycles” much, the setting is too rich. Turn the high speed needle H until the setting sounds correct.

For optimum setting of the carburetor, contact a qualiﬁed servicing dealer who has a revolution counter at his disposal.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine accelerates without hesitation and the machine 4-cycles a little at max speed. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difﬁculties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine. If the L and H-jets are set too rich it will lead to acceleration problems or too low a working speed.

Starter

WARNING! When the recoil spring is wound

!up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury. Always be careful when changing the recoil spring or the starter cord. Always wear protective goggles.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley.

Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the centre of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

CAUTION! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out.

Changing a broken recoil spring

•Lift off the pulley. See instructions under heading Changing a broken or worn starter cord.

•Remove the recoil spring from inside the pulley by tapping the pulley lightly with its inside face downwards against a work bench or the like. If the spring pops out during ﬁtting, wind it up again, working from the outside in towards centre.

•Lubricate the recoil spring with light oil. Fit the pulley and tension the recoil spring.

English – 29

CS 2141 EPA II, CS 2145 EPA II, CS 2150 EPA I specifications

The Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II are premium chainsaws engineered for both professional users and serious enthusiasts. These models exemplify Jonsered's commitment to power, efficiency, and user-friendly design, making them ideal for a variety of cutting tasks, from felling trees to trimming branches.

The Jonsered CS 2150 EPA I is a robust chainsaw that offers a powerful engine combined with advanced features. It boasts a 50.2 cc engine that delivers exceptional cutting performance while adhering to strict EPA emissions standards. The chainsaw is equipped with the X-Torq engine technology, which significantly reduces fuel consumption and emissions, enabling users to work longer while minimizing environmental impact. Additionally, the CS 2150 features a high chain speed of 22.3 m/s, allowing for swift and clean cuts.

The CS 2145 EPA II further enhances performance with its lightweight design, making it easy to maneuver for prolonged use without fatigue. Powered by a 45.7 cc engine, it combines efficiency with raw power, providing reliable performance for both professionals and homeowners. The inclusion of an easy-start system means that users can start the saw with minimal effort, which is especially advantageous during colder weather or when working in challenging environments. Its validated safety features, including a chain brake and low kickback bar, ensure user protection during operation.

The CS 2141 EPA II offers a perfect balance of power and manageability. With a smaller 40.9 cc engine, it is particularly suited for users looking for an efficient saw that doesn't compromise on performance. The lightweight design allows for easy handling, particularly in dense and difficult terrain. Like the other models, it utilizes the X-Torq engine technology, which ensures reduced emissions and optimal fuel efficiency. Its precise design and ergonomic handle make it comfortable for extended periods of use, catering to both professional loggers and landscape maintenance users.

Each of these models shares characteristics such as an efficient air filtration system, which prolongs engine life by keeping dirt and debris out. In addition, they are designed with vibrations dampening technology, reducing fatigue for the user. The easy access to the filter and spark plug simplifies maintenance, ensuring the chainsaws remain in peak condition.

In conclusion, the Jonsered CS 2150 EPA I, CS 2145 EPA II, and CS 2141 EPA II represent a solid lineup of chainsaws that combine power, efficiency, and safety. With advanced technologies and thoughtful design, they cater to a wide range of cutting needs, making them indispensable tools for anyone serious about their work in forestry, landscaping, or yard maintenance.

Jonsered CS 2141 EPA II Starter, Correctly adjusted carburettor, Tensioning the recoil spring

Models: CS 2141 EPA II CS 2145 EPA II CS 2150 EPA I