SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 24)

Park tractor on a level surface. Engage parking brake.

Lower mower to its lowest position.

Disengage belt tention rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

Remove screws from R.H. mandrel cover and remove cover.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Disconnect R.H.suspension arm from rear deck bracket by removing retainer spring.

Roll belt over the top of R.H. mandrel pulley carefully.

Remove belt from electric clutch pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

MOWER DRIVE BELT INSTALLATION (See Fig. 24)

Install belt in both idlers.

Install new belt onto electric clutch pulley.

Roll belt into upper groove of R.H. mandrel pulley care- fully.

Carefully check belt routing making sure belt is in the grooves correctly.

Reconnect R.H. suspension arm to rear deck bracket with retainer spring.

Reassemble R.H. mandrel cover.

Engage belt tension rod by pushing rod into locking bracket.

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 25)

Park the tractor on level surface. Engage parking brake.

Remove mower drive belt (See “TO REPLACE MOWER DRIVE BELT” in this section of this manual).

Remove mower (See “TO REMOVE MOWER” in this section of this manual).

Remove screws from L.H. mandrel cover and remove cover.

Carefully roll belt off L.H. mandrel pulley.

Remove belt from center mandrel pulley, idler pulley, and R.H. mandrel pulley.

Remove any dirt or grass which may have accumulated around mandrels and entire upper deck surface.

Check secondary idler arm and idler pulley to see that they rotate freely.

Be sure spring is hooked in secondary idler arm and secondary spring arm.

Install new belt in lower groove of R.H. mandrel pulley, idler pulley, and center mandrel pulley as shown.

Carefully roll belt over L.H. mandrel pulley. Make sure belt is in all grooves properly.

Reinstall L.H. mandrel cover.

Reinstall mower to tractor (See “INSTALL MOWER AND DRIVE BELT” in the Assembly section of this manual).

Reassemble mower drive belt (See “TO REPLACE MOWER DRIVE BELT” in this section of this manu- al).

SECONDARY

L.H. MANDREL IDLER ARM

IDLER PULLEY

SPRING

SECONDARY

SPRING ARM

CENTER

BELT

RH

TENSION ROD

SUSPENSION

(DISENGAGED

POSITION)

ARM

 

IDLER

PULLEY

SPRING

ARM

PRIMARY

IDLER ARM

R.H.

MANDREL

RH MANDREL COVER

ELECTRIC

CLUTCH

PULLEY

IDLER

PULLEY

MANDREL

R.H.

MANDREL

COVER

FIG. 25

TO CHECK AND ADJUST BRAKE (See Fig. 26)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved

FIG. 24

surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

22

Page 22
Image 22
Jonsered LT2119A To Replace Mower Drive Belt, To Replace Mower Blade Drive Belt See Fig, To Check and Adjust Brake See Fig

LT2119A specifications

The Jonsered LT2119A is a robust and efficient lawn tractor, designed to cater to the needs of homeowners seeking a reliable solution for their mowing and gardening tasks. With an emphasis on performance, comfort, and user-friendliness, the LT2119A showcases a blend of innovative engineering and practical features that make it ideal for various lawn conditions.

One of the standout features of the LT2119A is its powerful 19 horsepower Briggs & Stratton engine. This four-stroke engine ensures smooth operation while delivering sufficient power to tackle both small and large lawns. The engine's design emphasizes fuel efficiency and low emissions, aligning with modern environmental standards and reducing the overall cost of operation.

The LT2119A comes equipped with a 97 cm (approximately 38 inches) cutting deck that enables users to cover substantial ground in a single pass. The cutting height is easily adjustable, allowing for a customized mowing experience based on the specific conditions of the lawn. This versatility ensures that the tractor delivers a clean and even cut, regardless of grass type or height.

Another notable characteristic of the LT2119A is its superior maneuverability. The tractor is designed with a tight turning radius, allowing users to navigate around obstacles and tight spaces effortlessly. This feature optimizes efficiency, especially in intricate garden layouts or when mowing around trees and flower beds.

The ergonomic design of the LT2119A enhances user comfort during operation. It features a comfortable seat with a high backrest, which provides adequate support for longer mowing sessions. The steering wheel is positioned to ensure a relaxed grip, reducing strain on the arms and shoulders. Additionally, the simple control layout allows for intuitive operation, making it accessible for users of all experience levels.

The tractor also incorporates advanced technologies for enhanced functionality. The electric start system eliminates the hassle of pull cords, making it easier to start the engine with just the push of a button. The LT2119A is also equipped with a cutting blade engagement system that ensures quick and efficient blade operation.

In summary, the Jonsered LT2119A is a well-rounded lawn tractor that combines power, efficiency, and ease of use. With its strong engine, adjustable cutting deck, and comfortable design, it stands out as a reliable choice for homeowners looking to maintain their lawns effectively. Whether you're tackling overgrown grass or simply performing regular maintenance, the LT2119A provides the performance and features necessary for successful lawn care.