JVC CA-MXJ787V English, Only For “Pro Logic”, output balance, On the unit, Surround. with the

4 ONLY FOR “PRO LOGIC”

Press DELAY TIME repeatedly to select	DELAY TIME
the proper delay time of the rear speaker
output.

•Each time you press the button, the delay time changes as follows.

DELAY1 DELAY2

DELAY4 DELAY3

DELAY1: Select this when the distance from you to your rear (15 m Sec) speakers is greater than that to the front speakers. DELAY2: Select this when the distance from you to your rear (20 m Sec) speakers is almost equal to that to the front speakers. DELAY3: Select this when the distance from you to your rear (25 m Sec) speakers is less than that to the front speakers. DELAY4: Select this when the distance from you to your rear (30 m Sec) speakers is much less than that to the front speakers.

5 Press TEST TONE to check the speaker			TEST TONE
output balance.
A test tone comes out of the speakers in the following
order:
	LEFT	CENTER *
	(Left front speaker)	(Center speaker)
	SURROUND	RIGHT
	(Rear speakers)	(Right front speaker)

*“CENTER” does not appear when selecting “PHANTOM” or “OFF” for the center mode, and no test tone comes out of the center speaker.

Enjoying Playback with Dolby Surround

You can use the settings you have already stored in memory.

On the unit:

1 Press PRO LOGIC/3 STEREO c button to	/ 3 STEREO
	PRO LOGIC
select the Dolby Surround mode you want.

The PRO LOGIC or 3 STEREO indicator lights up on the display.

PRO LOGIC

3 STEREO

A

P

R

•Each time you press the button, the Dolby Surround modes changes as follows:

PRO LOGIC 3 STEREO

Cancelled

•When Dolby Surround is activated, the sound mode is cancelled temporarily.

2 Select and play a sound source encoded with Dolby

Surround. (with the		mark).
	DOLBY SURROUND

To cancel the Dolby Surround mode, press PRO LOGIC / 3 STEREO repeatedly until neither PRO LOGIC nor

3 STEREO indicator remains lit on the display.

English

6 Press VOLUME + / – ª to adjust the test tone volume to a proper level.

7 If necessary, adjust the speaker output balance so that the output level from center and rear speakers is almost equal to that from the front speakers:

To adjust the center speaker output – CENTERLEVEL + level (from –10 to +10),press CENTER

On the remote control:

1 Press and hold SHIFT 9 until the following procedure is finished.

2 Press PRO LOGIC or 3 STEREO	PRO LOGIC
c whichever you want to use.

The PRO LOGIC or 3 STEREO indicator lights up on the display.

SHIFT

3 STEREO

LEVEL – / +.

• You cannot adjust the center speaker output level

when you select “PHANTOM” or “OFF” for the center mode.

•When Dolby Surround is activated, the sound mode is cancelled temporarily.

3 Select and play a sound source encoded with Dolby

8

9

To adjust the rear speaker output level (from –10 to +10),press REAR LEVEL – / +.

•You cannot adjust the right and left speaker output levels separately.

•You cannot adjust the rear speaker output level when using Dolby 3 Stereo.

Press TEST TONE again to stop the test tone.

Release SHIFT 9.

–LEVELREAR +

TEST TONE

Surround. (with the		mark).
	DOLBY SURROUND

To cancel the Dolby Surround mode, press PRO LOGIC or 3 STEREO (the same button you have pressed to activate Dolby Surround in step 1 above) so that neither PRO LOGIC nor 3 STEREO indicator remains lit on the display.

*Manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY, the double-D symbol, and “PRO LOGIC” are trademarks of Dolby Laboratories Licensing Corporation.

20

EN18-20;MX-J777V/PM620

7/8/99, 9:13 AM