JVC DLA-G150HTE

DLA-G150HTE

1-7

No.51847

Controls and Features

ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL

Control Panel on the Projector

1STAND BY Indicator

ON : When in stand-by mode.

Blinking :When in cool-down mode.

Memo

About the cool-down mode:

This projector has a function to cool down the heated lamp for a

fixed period of time (approx. 120 seconds) after projection is

finished. This feature is referred to as the cool-down mode.

The purpose of the cool-down mode is to prevent inner parts

from being deformed or broken by heat from the heated lamp

as well as to prolong the life of the lamp.

CAUTIONS

•Do not turn off the MAIN POWER switch while in the cool-

down mode.

•Do not place the projector on its side or stand it upright

while in the cool-down mode; this may block the vents.

2OPERATE indicator

ON : When the projector is in operation (projecting).

OFF :When the projector is not in operation (not

projecting).

3OPERATE button

When the projector is in the stand-by mode, press this

button one second or more, and the projector is turned

on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector

goes into the cool-down mode, then stand-by mode.

(Refer to page31.)

*You cannot use the OPERATE button for about one

minute after the lamp blinks. Press the button after a

minute or longer has elapsed.

Memo

While in the cool-down mode (STAND BY indicator is blinking):

Even if you press the OPERATE button, the projector is not

turned on. Wait until the projector enters stand-by mode

(STAND BY indicator stays lit).

4PC button

Use this button to select a device connected to the PC 1

or PC 2 terminals. Each time you press the button, the

selection alternates between PC 1 and PC 2.

*“PC1” or “PC2” will be displayed on the top right of the

projected image. (This function can be disabled by the

menu.)

5VIDEO button

Use this button to select a device such as a video deck

connected to the AV IN (Y/C or VIDEO) terminal of the

projector. Each time you press the button, the selection

alternates between Y/C and VIDEO.

*“Y/C” or “VIDEO” wil l be displayed on the top right of the

projected image. (This function can be disabled by the menu.)

6MENU button

Use this button to enter or exit the menu mode. The main

menu appears or disappears at the screen. For details,

refer to “Basic Menu Operation” on page42.

7ENTER button

This button will be used in the menu mode. Use to

display the hierarchical menus. Also use when “ENTER”

is displayed against the item on the menu screen or

when the “All reset” selection is confirmed. For details,

refer to “Basic Menu Operation” on page42.

8Cursor buttons 5/∞/2/3

These buttons will be used in the menu mode to select an

item, or to set or adjust the value. For details, refer to

“Basic Menu Operation” on page42.

VIDEO

LAMPTEMPSTAND BY

KEYSTONE

PRESET

EXITENTER

OPERATE

HIDE

LAMP TEMP STAND BY

HIDE

VIDEO

KEYSTONE

PRESET

EXIT ENTER

OPERATE

Controls and Features

9EXIT button

This button will be used in the menu mode to return to the

previous menu. When the main menu is displayed, this

button will cause the menu to disappear. For details, refer

to “Basic Menu Operation” on page42.

pPRESET button

This PRESET button only works as a reset button for the

direct button adjustment of the KEYSTONE button of the

control panel and the DIGITAL ZOOM button of the

remote control. When adjusting the keystone or digital

zoom (when the setting is displayed on the screen) the

adjusted value is reset to that which was set when the

projector was shipped from the factory. Of the menu

items, this button only works for the keystone setting

screen.

qKEYSTONE / buttons

Use these buttons to correct a trapezoidal distortion of

the projected image. (Refer to page34.)

wHIDE button

Use this button to turn off the image on the screen

temporarily. Pressing it again restores the image to

resume. (Refer to page34.)

eLAMP indicator

ON : After the light-source lamp has been used for

more than approx. 900 hours.

Blinking

:After the light-source lamp has been used for

more than approx. 1000 hours. Replace the light-

source lamp. Refer to “Replacing the Light-

Source Lamp” on page57.

rTEMP indicator

Blinking :The temperature inside the projector has risen

abnormally.

Note

•While the TEMP indicator is blinking (during abnormal

temperature), the power is automatically cut off.