JVC DLA-G150HTE

DLA-G150HTE

1-8 No.51847

Controls and Features

Remote Control Unit

On the remote control, the same buttons as on the control

panel of the projector are provided except for the following

buttons. For the same buttons, operation is the same in

principle.

For remote control only:

DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/

W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C

1Remote control’s signal transmitter

2OPERATE button

When the projector is in the stand-by mode, press this

button one second or more, and the projector is turned

on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector

goes into the cool-down mode, then stand-by mode.

(Refer to page31.)

*The OPERATE button will not work for approximately 1

minute from when the light-source lamp is turned on. Use

the button after approximately 1 minute.

Memo

While in the cool-down mode (STAND BY indicator is

blinking):

Even if you press the OPERATE button, the projector is not

turned on. Wait until the projector enters stand-by mode

(STAND BY indicator stays lit).

3HIDE button

Use this button to turn off the image on the screen

temporarily. Pressing it again makes the image to

resume. (Refer to page34.)

4FREEZE button

During projection of an image on the screen, press this

button to obtain a still picture.

To restore normal projection, press it again. (Refer to

page36.)

*Depending on the video signal source (UXGA, etc.), this

button does not work.

5VIDEO button

Use this button to select a device such as a video deck

connected to the AV IN terminal (VIDEO or Y/C input

terminal) of the projector. Each time you press the button,

the selection alternates between Y/C and VIDEO. (Refer

to page32.)

*“Y/C” or “VIDEO” will be displayed on the top right of the

projected image. (This function can be disabled by the

menu.)

6ZOOM T/W buttons

Use these buttons to adjust the projected screen size.

T (Tele): The projected screen size decreases.

W (Wide):The projected screen size increases.

7FOCUS +/– buttons

Use these buttons to adjust the focus of the projected

video image.

+ : The focus point becomes more distant.

– : The focus point becomes nearer.

8MENU button

Use this button to enter or exit the menu mode. The main

menu appears or disappears at the screen. For details,

refer to “Basic Menu Operation” on page42.

9Cursor buttons 5/∞/2/3

These buttons are used in the menu mode to select an

item or to set or adjust the value. For details, refer to

“Basic Menu Operation” on page42.

pENTER button

This button is used in the menu mode. Use to display the

hierarchical menus. Also use when “ENTER” is displayed

against the item on the menu screen or when the “All

reset” selection is confirmed. For details, refer to “Basic

Menu Operation” on page42.

qEXIT button

This button is used in the menu mode to return to the

previous menu. When the main menu is displayed, this

button will cause the menu to disappear. For details, refer

to “Basic Menu Operation” on page42.

wPRESET button

This PRESET button only works as a reset button for the

direct button adjustment of the KEYSTONE button of the

control panel and the DIGITAL ZOOM button of the

remote control. When adjusting the keystone or digital

zoom (when the setting is displayed on the screen) the

adjusted value is reset to that which was set when the

projector was shipped from the factory. Of the menu

items, this button only works for the keystone setting

screen.

eKEYSTONE / buttons

Use these buttons to correct a trapezoidal distortion of

the projected image. (Refer to page34.)

QUICK

ALIGN.

PC1 PC2 Y/C

VIDEO

HIDE

PRESET

ENTEREXIT

FREEZE

SCREEN

OPERATE

DIGITAL

ZOOM

ZOOM FOCUS

RM-M150 REMOTE CONTROL UNIT

SCREEN

KEYSTONE

Controls and Features

ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL

Connector Panel

1Y/C (S-video) input terminal (Mini DIN 4 pin)

Connect this terminal to the S-video output terminal of a

video deck, etc.

Attach the ferrite core (accessory) to the cable which is

connected to the Y/C input terminal. (Refer to page 29.)

VIDEO (composite video) input terminal (BNC)

Connect this terminal to the composite video output

terminal of a video deck, etc.

3REMOTE terminal (stereo mini jack)

Connect an infrared remote control extension unit, etc. to

this jack.

Attach the ferrite core (accessory) to the cable which is

connected to the REMOTE terminal. (Refer to page 29.)

*For details, consult your dealer.

4RS-232C CONTROL terminal (D-sub 9 pin)

This is the RS-232C interface-specified terminal. The

projector can be controlled by a computer connected

externally.

*For details, refer to page 27 and 71.

5PC (computer) OUT terminal (D-sub 3-row 15 pin)

This is the terminal for video output from the monitor of

the computer connected to PC1 or PC2.

The computer input signal projected on the screen is

output. A display monitor can be used by connecting it to

this terminal.

6PC (computer) 2 input terminals (BNC

××

These are multipurpose video input terminals that allow

input of the following signals.

•Analog RGB signals, vertical sync (V) signals, and

horizontal sync (H) signals / composite signals (Cs).

(Devices which have analog RGB signal output

terminals can be connected.)

*Input of external sync signals is automatically detected.

Detection of H/V signals or Cs signals causes automatic

switching to external sync. The priority order is H/V > Cs.

•Component signals (Y, B-Y, R-Y) or DTV-format (Y, P

) signals. (Devices which have component output

terminals can be connected.)

*For details about DTV-format signals (480i, 480p, 720p,

1080i) compatible with this unit, refer to page22.

Notes

•In order to use this terminal, the input signal must be used

to select the “PC 2 (BNC)” setting in the option items of the

menu. Use the input signal to change the setting. (Refer to

page53.)

•When computer-related signals are input, the uppermost

edge of the image may appear to bow if the sync signal

input is composite sync (Cs) or G on sync signal. In this

case, use separate sync signals for vertical sync (V) and

horizontal sync (H).

7PC (computer) 1 input terminal (D-sub 3-row 15

pin)

This is an input terminal dedicated to computer signals

(RGB video signals and sync signals).

Connect the display output terminal of the computer to

this terminal. When a Macintosh computer is to be

connected, use the supplied conversion adapter for Mac.

Note

•When computer-related signals are input, the uppermost

edge of the image may appear to bow if the sync signal

input is composite sync (Cs) or G on sync signal. In this

case, use separate sync signals for vertical sync (V) and

horizontal sync (H).

VIDEO

LAMPTEMPSTAND BY

KEYSTONE

PRESET

EXITENTER

OPERATE

HIDE

/B-Y

/R-Y

REMOTE

RS-232C

Y/C VIDEO