EN 57

1 Load the provided memory card. ( pg. 16)

 

 

Insert Editing

 

 

 

 

Then, perform step 1 and 2 of “Audio Dubbing”

 

 

 

( pg. 56).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 Press MENU. The Menu Screen appears.

You can record a new scene into a previously

recorded tape, replacing a section of the original

3 Press + or – to select “s”, and press SET/

recording with minimal picture distortion at the in

SELECT. The SYSTEM Menu appears.

and outpoints. The original audio remains

4 Press + or – to select “SOUND IN”, and press

unchanged.

 

SET/SELECT. The Sub Menu appears.

 

 

 

 

 

 

 

 

 

 

 

 

 

5 Press + or – to select “D.SOUND”, and press

 

 

 

 

 

 

 

 

 

 

 

 

START/STOP

 

 

 

 

 

 

 

 

 

 

 

 

SET/SELECT.

 

 

 

 

 

 

 

 

 

 

 

 

INSERT

6 Press + or – to select “BRETURN”, and press SET/

 

 

REW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLAY

SELECT twice. The Menu Screen closes and the

 

 

 

 

 

 

 

 

 

 

 

 

 

sound effect indication appears.

 

 

STOP

 

 

 

 

 

 

 

 

 

PAUSE

7 Press INDEX to access the sound effects Index

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

8 Press + or – to select the desired sound effect and

NOTES:

 

press SET/SELECT.

● Before performing the following steps, make sure

9 Press PLAY (U) to begin Audio Dubbing. The

 

that “TIME CODE” is set to “ON”. ( pg. 31, 41)

selected sound effect is dubbed onto the tape.

● Insert Editing is not possible on a tape recorded in

● The “ ” moves while it is being dubbed.

 

the LP mode or on a blank portion of a tape.

● To stop dubbing the sound effect midway, press

● To perform Insert Editing while watching in the

D.SOUND.

 

television, make connections. ( pg. 22)

10 Press STOP (8) to end Audio Dubbing.

1 Play back the tape, locate the Edit-Out point and

NOTES:

 

 

press PAUSE (9). Confirm the time code at this

 

 

point. ( pg. 41)

 

● After dubbing, set “SOUND IN” back to “MIC/

 

 

 

2 Press REW (3) until the Edit-In point is located,

AUX”.

● The dubbed sound effect is recorded on

 

 

then press PAUSE (9).

 

SOUND 2. ( pg. 40)

3 Press and hold INSERT (I) on the remote

● If you press PAUSE (9) to pause dubbing in step 9

 

 

control, then press PAUSE (9). The “9I”

the selected sound effect indication remains

 

 

indicator and the Time Code (min.:sec.) appear

displayed. To resume dubbing, press PLAY (U).

 

 

and the camcorder enters Insert-Pause mode.

 

4 Press START/STOP to begin editing.

 

 

 

 

● Confirm the insert at the time code you

checked in step 1.

● To pause editing, press START/STOP. Press it again to resume editing.

5 To end Insert Editing, press START/STOP, then STOP (8).

NOTES:

● Program AE with special effects ( pg. 33) can be used to spice up the scenes being edited during Insert Editing.

● During Insert Editing, the date and time information changes.

● If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

● During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Edting stops. ( pg. 80, 81)

● If a memory card is loaded and “NAVIGATION” is set to other than “MANUAL”, a NAVIGATION thumbnail image is stored in the memory card. ( pg. 47)