JVC UX-J55V, GVT0116-003B manual Turning On the Power, Adjusting the Volume, Enjoying Sound Effects

Continued

English

Turning On the Power

To turn on the unit, press	STANDBY/ON
STANDBY/ON .
The STANDBY/ON lamp lights
green and “HELLO” appears on
the display.

•When you press the source button—CD 3/8, TAPE 2 3, FM/AM, and AUX, the unit automatically turns on and starts playback if the source is ready.

To turn off the unit (standby), press STANDBY/ON again.

The STANDBY/ON lamp lights red and “GOOD BYE” appears on the display.

•“0:00” flashes on the display until you set the built-in clock. After setting the clock, the clock time will appear on the display while the unit is on standby.

The illumination and display brighten only for 4 seconds by pressing DIMMER.

•A little power is always consumed even while the unit is on standby.

To switch off the power supply completely, unplug the AC

power cord from the AC outlet.

When you unplug the AC power cord or if a power failure occurs

The clock is reset to “0:00” right away, while the tuner preset stations (see page 12) will be erased in a few days.

Adjusting the Volume

You can adjust the volume level only while the unit is turned on. The volume level can be adjusted between “VOL MIN” and “VOLUME 1” – “VOLUME 40 (VOL MAX).”

On the remote control:

Press VOLUME + to increase the volume or press VOLUME – to decrease it.

Enjoying Sound Effects

You can adjust the sound by using various sound effect functions.

•These functions only affect the playback sound, and do not affect your recording.

To adjust the tone (Bass/Treble)

You can adjust the bass level (low frequency range) and the treble level (high frequency range) within a range of –5 to +5. When shipped, the bass level set to “BASS +2” and the treble level set to “TREBLE +2.”

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start over from step 1.

•For UX-J55V only, you can also use BASS and TREBLE on the unit for this operation.

1 Press BASS to adjust the BASS TREBLE

bass level or press TREBLE to adjust the treble level.

•Each timer you press the button,

“BASS” and “TREBLE” appears in the display alternately.

UP

2 Press UP to increase the level or press DOWN to decrease it.

DOWN

To reinforce the bass sound

You can reinforce the bass sound to maintain rich, full bass at low volume—Active Hyper Bass Pro.

For UX-J66V:
Press AHB PRO.	PRO
	AHB

• Each time you press the button, the Active Hyper Bass Pro is turned on (AHB ON) and off (AHB OFF) alternately. When it is turned on, the AHB indicator lights up on the display.

On the unit:

VOLUME

AHB

Turn VOLUME + / – control clockwise

(+)to increase the volume or counterclockwise (–) to decrease it.

For private listening

Connect headphones to the PHONES jack.

No sound comes out of the speakers. Be sure to turn down the volume before connecting or putting on headphones.

DO NOT turn the unit off (standby) with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the unit or start playing any source next time. REMEMBER you cannot adjust the volume level while the unit is on standby.

For UX-J55V:
Press AHB PRO until “AHB 1” or “AHB 2”	PRO
	AHB
appears on the display.

The AHB indicator also lights up on the display.

•Each time you press the button, the bass reinforcement changes as follows:

AHB 1 AHB 2 AHB OFF (Canceled)

•“AHB 2” has much more bass reinforcement effect than “AHB 1.”

To cancel the effect, press AHB PRO until “AHB OFF” appears on the display and the AHB indicator goes off.

10