JVC HR-J781AM manual Express Timer Programing, Access Program screen, Select program to modify

[PROG] : EXIT

[ / ]

PR START STOP CH DATE

1 8:00 10:00 3 24.04

2 10:00 10:45 2 25.04

3 11:30 13:00 1 25.04

4 9:00 10:00 92 DAILY

5

6

7

8

STOP 10:00

SP

START 8:00

– P1 –

– Timer Recording –

Express Timer Programing

●Remember, the clock must be set before you can program the timer.

●Load a cassette with the record safety tab intact. The recorder turns on, and the counter is reset, automatically.

●Select the appropriate colour system with “PAL/MESECAM” and “NTSC” in Function settings.

BAccess Program Check screen

Press ".

CAccess Program screen

Press " again. Each time you press ", the next program’s Program screen appears.

PR START		STOP	CH	DATE
1	8:00	10:00	3	24.04
2	10:00	10:45	2	25.04
3	11:30	13:00	1	25.04
4
5
6
7
8
[	] : NEXT
	START	– P1 –	STOP
	8:00		10:00
			SP
	DATE		TV PROG

24.043

[ ] : NEXT

APress PROG on the remote control to access the G-CODE/ SHOWVIEW screen, then press START+/–.

B Press START+/–,STOP+/–,DATE+/–

or PR+/– repeatedly to enter the start time, stop time, date or channel.

● Press and hold START+/– or

STOP+/– to increase the time in	DATE	TV PROG
	24.04	3
30-minute intervals.
	[+/–]
● To set the tape speed, press SP/LP/	[PROG] : EXIT
EP (p).

●To timer-record daily (Monday–Friday) or weekly serials, press DAILY or WEEKLY. Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

CPress OK or PROG.

●If “PROGRAM OVERLAPPED” appears, see “Program overlap warning display”.

DPress #. The recorder turns off automatically and “#” is displayed on the display panel.

NOTE:

If the tape reaches its end during timer recording, the recording stops and “#” , “” and “e” on the front display panel blink.

To use the recorder while it is in timer recording standby mode

Press #, then press 1. After you use the recorder, press # again to put the recorder into timer recording standby mode.

Checking, cancelling or changing program settings

ADisengage timer

DCancel or change program setting

To cancel a program, press & when the Program screen you do not want is shown.

To change a program, press the appropriate button: START+/–, STOP+/–, DATE+/–, PR+/–, and/or SP/LP/EP (p) when the Program screen on which you want to make changes is shown.

EReturn to normal screen

Press " repeatedly until no Program screen is shown.

FReengage timer recording standby mode

Press #. The recorder turns off automatically and “#” is displayed on the display panel.

●When “AUTO TIMER” is set to “ON”, the timer recording standby mode automatically resumes when you turn off the recorder.

Program overlap warning display

If “PROGRAM OVERLAPPED” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.

	PR START		STOP	CH	DATE
PROGRAM OVERLAPPED	1	8:00	10:00	3	24.04
	2	10:00	10:45	2	25.04
	3	11:30	13:00	1	25.04
	4	9:00	10:00	92	DAILY
	5
	6
	7
	8
	[	/ ]	[PROG] : EXIT

Example:

Program 1 (you have just made) and Program 4 overlap each other.

A Select program to modify

Press rt, then press e.

● You can only select one of the overlapping programs.

● If you do not mind this overlap, press

PROG to finish the timer program setting. The program starting earlier or

program with the lower program number will be recorded.

B Cancel or change program setting		– P1 –
To cancel a program, press & when the	START	STOP
	9:00	10:00
Program screen you do not want is shown.		SP
To change a program, press the	DATE	TV PROG
appropriate button: START+/–, STOP+/–,	25.04	92
DATE+/–,PR+/–, and/or SP/LP/EP (p)	[ ] : DELETE	[+/–]
	[PROG] : EXIT

when the Program screen on which you

want to make changes is shown, then press OK.

●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.

Press #, then press 1.

●When “AUTO TIMER” is set to “ON”, you do not have to press #.