December 21, 2001 9:51 am Page 10
—10—
Master Page: Right
24 Hour Express Timer Programming
You can programme a timer recording that starts within 24hours.
APress 24H EXPRESS#. The start time
indicator ( ) starts blinking on the display
panel.
BTurn the JOG dial to the left or right to
set the start time.
●One click stop of the JOG dial changes
the time in 5-minute intervals.
CPush the JOG dial. The stop time
indicator ( ) starts blinking on the display
panel. Turn the JOG dial to the left or right
to set the stop time.
DPush the JOG dial. Turn the JOG dial to
the left or right to select the channel.
●To set the tape speed, press SP/LP (p).
The current setting for the tape speed
appears on the display panel for about 5seconds. Press SP/LP
(p) again to change the setting while tape speed is displayed.
●You can cancel the setting at any time by pressing and holding
the JOG dial for more than 3seconds. Repeat the steps 2
22
2–4
44
4.
EPress 24H EXPRESS#. The recorder turns off automatically
and “#” is displayed on the display panel.
NOTES:
●If “Err” appears on the display panel, repeat the above steps
again.
●When a menu screen is shown, you cannot use 24Hour Express
Programming function. Press MENU to return to normal screen,
and try again.
●You can use 24Hour Express Programming function also when
the recorder is turned off.
Checking, canceling or changing programme settings
ADisengage timer recording standby mode
Press #, then press 1.
●When “AUTO TIMER” is set to “ON” (墌12), press only 1.
BAccess Program Check screen
Press ".
CAccess Program screen
Press " again. Each time you press ",
the next programme’s screen appears.
DCancel or change programme setting
To cancel a programme, press &.
To change a programme, press the
appropriate button:START+/–, STOP+/–,
DATE+/– , DAILY, WEEKLY, PR+/–, VPS/PDC and/or SP/LP (p).
●To change “TV PROG” to “SAT” for the channel position, press
the number key “0”.
EReturn to normal screen
Press " repeatedly until no Program screen is shown.
FRe-engage timer recording standby mode
Press #. The recorder turns off automatically and “#” is displayed
on the display panel.
●When “AUTO TIMER” is set to “ON” (墌12), the timer
recording standby mode automatically resumes when you turn
off the recorder.
Automatic Satellite Programme Recording
You can automatically record a satellite programme which is
timer-programmed on your satellite receiver.
AConnect a satellite receiver to the L-2 IN/DECODER connector
on the rear panel.
BSet timer programme on satellite receiver referring to its
instruction manual.
CLoad a cassette with the record safety tab intact.

DSet “L-2 SELECT” to “A/V” or “SAT”. (墌13)

ETo set the tape speed, press SP/LP (p). The current setting for
the tape speed appears on the display panel or the screen for
about 5seconds. Press SP/LP (p) again to change the setting
while tape speed is displayed.
FPress SAT# for more than 2seconds. The recorder turns off
automatically and enter the Automatic Satellite Programme
Recording mode (the SAT# indicator lights up). When signals
come into the recorder from the satellite receiver, the recorder
starts recording (the SAT# indicator blinks). The recorder stops
recording and turns off when signals stop coming in.
NOTES:
●Be sure not to turn on the satellite receiver before the
programme starts broadcasting; otherwise, the recorder starts
recording when the satellite receiver is turned on.
●To disengage the Automatic Satellite Programme Recording
mode, press SAT# (the SAT# indicator goes off).
●Depending on the type of satellite receiver, Automatic Satellite
Programme Recording may not be compatible.
●B.E.S.T. does not work in the Automatic Satellite Programme
Recording mode.
●Power Save mode does not work in the Automatic Satellite
Programme Recording mode.
●Just Clock does not work in the Automatic Satellite Programme
Recording mode.
Start time
Stop time
Channel
HR-J790EU-001EN.fm Page 10 Friday, December 21, 2001 9:51 AM