JVC HR-S2901/2911U Timer Recording, Express Timer Programing, Program overlap warning display

PR START STOP CH DATE

1 8:00P 10:00 12 12/24

2 10:00A 10:45 40 12/25

3 11:30P 1:00 125 12/25

4 9:00P 10:00 10 12/24

5

6

7

8

( , ) THEN ( ) (PROG.) : END

Timer Recording

Up to 8 timer recording programs can be made using express timer programing method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

●If all the 8 programs have already been set, “PROGRAM FULL” appears on the TV screen.

●After timer recording is completed, the VCR turns off automatically.

●You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●To timer-record cable or satellite channels, be sure to keep the cable box or DBS receiver turned on with the correct channel selected.

●Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost. As a result, when the power is supplied again to this VCR after the power failure, this VCR starts the Plug&Play setting automatically to restore the clock time and channel setting. If the clock time and channel setting are restored correctly, each timer program you have made will start at its start time unless its end time has elapsed.

NOTE:

If the tape reaches its end during timer recording, the recording stops and “ #“, “ ” and “ $” on the display panel blink. Press TIMER to disengage timer, then press STOP/EJECT (0) on the VCR to eject the cassette or press POWER 1 then press REW (3) to rewind the tape.

Express Timer Programing

Load a cassette with the record safety tab intact. The VCR turns on, and the counter is reset, automatically.

APress PROG. on the Remote to access the Program screen.

B Press START+/–,STOP+/–,DATE+/– or		PROGRAM 1
CH+/– repeatedly to enter the start		START	STOP
time, stop time, date or channel.		– –:– –AM	– –:– –AM
		DATE	CH
● Press and hold START+/– or STOP+/–
		– –/– –/– –	– – –	SP
to increase the time in 30-minute
	PRESS (+/–, SP/EP, 8=DAILY
intervals.	9=WEEKLY), THEN (0K)
● To set the tape speed, press SP/EP.	PRESS (PROG.) TO END

● To timer-record daily (Monday–Friday) or weekly serials, press DAILY (M-F) (Number key “8”) or WEEKLY (Number key “9”). Pressing the button again makes the “DAILY” or “WEEKLY” display disappear.

CPress OK or PROG..

●If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, see “Program overlap warning display” ( pg. 10).

DPress TIMER. The VCR turns off automatically and “#” is displayed on the display panel.

To use the VCR while it is in timer recording standby mode

Press TIMER, then press POWER 1. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode.

Checking, canceling or changing program settings

ADisengage timer

Press TIMER, then press POWER 1.

●When “AUTO TIMER” is set to “ON” ( pg. 11), you do not have to press TIMER.

B Access Program Check screen	PR START		STOP	CH	DATE
Press PROG. CHECK.	1	8:00P	10:00	12	12/24
	2	10:00A	10:45	40	12/25
C Access Program screen	3	11:30P	1:00	125	12/25
	4
	5
Press PROG. CHECK again. Each time you	6
	7
press PROG. CHECK, the next program’s	8
		PRESS (CHECK) TO NEXT

Program screen appears.

D Cancel or change program setting

To cancel a program, press CANCEL when the Program screen you do not want is shown.

To change a program, press the appropriate button: START+/–, STOP+/–, DATE+/–, CH+/–, DAILY (M-F) (Number key “8”), WEEKLY (Number key “9”) and/or SP/EP when the Program screen on which you want to make changes is shown.

EReturn to normal screen

Press PROG. CHECK repeatedly until no Program screen is shown.

FReengage timer recording standby mode

Press TIMER. The VCR turns off automatically and “#” is displayed on the display panel.

●When “AUTO TIMER” is set to “ON” ( pg. 11), the timer recording standby mode automatically resumes when you turn off the VCR.

Program overlap warning display

If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking.

	PR START		STOP	CH	DATE
PROGRAM NOT COMPLETED	1	8:00P	10:00	12	12/24
	2	10:00A	10:45	40	12/25
PROGRAM OVERLAP	3	11:30P	1:00	125	12/25
	4	9:00P	10:00	10	12/24
	5
	6
	7
	8
	(	, ) THEN ( ) (PROG.) : END

Example:

Program 1 (you have just made) and Program 4 overlap each other

A Select program to modify

Press rt, then press OK or e.

● You can only select one of the overlapping programs.

● If you do not mind this overlap, press

PROG. to finish the timer program setting. The program starting earlier or

program with the lower program number will be recorded.

B Cancel or change program setting		PROGRAM 4
To cancel a program, press CANCEL when	START	STOP
the Program screen you do not want is	9:00PM	10:00PM
	DATE	CH
shown.	12/24/02	10 SP
	TUE
To change a program, press the
	PRESS (CANCEL) TO CANCEL
appropriate button: START+/–, STOP+/–,	PRESS (OK) TO CONFIRM
	PRESS (PROG.) TO END
DATE+/–,CH+/–,DAILY (M-F) (Number

key “8”), WEEKLY (Number key “9”) and/or SP/EP when the Program screen on which you want to make changes is shown, then press OK or e.

●If the overlap is not yet solved, the conflicting programs will be shown on the Program check screen. Repeat the above steps again.

— 10 —