ELECTRICAL CONNECTIONS
Make sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.
High
Note:
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 14 of the INSTRUCTIONS).
Heat sink
Typical connections
Rear ground terminal | Line out |
Connecting the external amplifiers and/or subwoofer
Remote lead |
Antenna terminal
To external component
Connect only the front speakers if your speaker system is
White with black stripe
Front speaker (left) | White |
Gray with black stripe
Front speaker (right) | Gray |
|
|
|
|
|
|
| 15 A fuse |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| Black | To metallic body or | |||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| chassis of the car |
To a live terminal in the
Yellow *2 fuse block connecting to the 
car battery (bypassing the
ignition switch) (constant 12 V)
Red | To an accessory terminal in |
| the fuse block |
Ignition switch
Fuse block
JVC Amplifier
Rear speakers
Set “L/O MODE” to “REAR”
(See page 14 of the INSTRUCTIONS.)
JVC Amplifier
Remote lead (blue with white stripe)
To the remote lead of other equipment or automatic antenna if any
Front speakers
JVC Amplifier
Green with black stripe
Rear speaker (left) | Green |
Purple with black stripe
Blue with white
stripeTo the remote lead of other 
equipment or automatic antenna if
any (200 mA max.)
Front speakers
or
Set “L/O MODE” to “WOOFER” (See page 14 of the INSTRUCTIONS.)
Front 
speakers
Rear speaker (right) | Purple |
PRECAUTIONS on power supply and speaker connections
JVC Amplifier
Subwoofer
*1 Not supplied for this unit.
*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.
*3 Firmly attach the ground wire to the metallic body or to the
chassis of the
*4 Signal cord (not supplied for this unit).
Connecting the external components
(A)JVC CD changer, SIRIUS Satellite radio, XM Satellite radio, Apple iPod®, or JVC D. player
Set “CHANGER” for the external input setting (See page14 of the INSTRUCTIONS.)
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
•For listening to the SIRIUS Satellite radio, connect a JVC
•The iPod*5 or D. player (separately purchased) can be connected using an interface adapter (not
CD changer jack
•For listening to the XM Satellite radio, you can also connect XMDirectTM Universal Tuner Box (separately purchased) through this unit using JVC Smart Digital Adapter— XMDJVC100 (not supplied).
|
|
| XMDirectTM Universal Tuner Box |
| XMDJVC100 | |
Antenna (supplied |
|
| ||||
|
|
|
| |||
|
|
|
| |||
with XMDirectTM | To CD changer, | |||||
Universal Tuner Box) | ||||||
connection) |
|
| ||||
|
|
|
|
| ||
|
|
|
|
|
| |
Connection 1 (integrated connection) | |
JVC DLP | Apple iPod |
| or |
| JVC D. player |
| or |
or | JVC CD changer |
| |
Connection 2 (alternative connection)
JVC DLP
or
JVC CD changer
or
Apple iPod
or
JVC D. player
*5 | iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. |
*6 | Signal cord supplied with your JVC CD changer or DLP. |
(B) JVC PnP (Plug and Play)
Set “EXT IN” for the external input setting (See page14 of the INSTRUCTIONS.)
You can also connect JVC PnP through this unit using JVC SIRIUS radio adapter,
• Turning on/off the unit can also turns on/off the JVC PnP.
To headphones jack
| Stereo mini plug |
| JVC PnP |
CD changer jack | DC power plug |
To DC IN jack
(C) Other external component
You can also connect an external component through this unit using Line Input Adapter,
Signal cord (not supplied for this unit)
External
component
CD changer jack
External |
component |
3.5 mm stereo mini plug |
2
