P.CONT
ANT.CONT
MUTE
REMOTE CONT
STEERING WHEEL
REMOTE INPUT
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
L
R
L
R
Yellow (Battery wire)
Red (Ignition wire)
FM/AMantennainput(JASO)
Antenna Cord
Wiring harness
(Accessory 1)
If no connections are made, do not
let the wire come out from the tab.
Blue/White (Power control/
Antenna control wire)
Brown (Mute control wire)
Connect either to the power control terminal when
using the optional power amplifier, or to the antenna
controlterminalinthevehicle.(Max.300mA,12V)
Red (A–7 Pin)
Yellow (A–4 Pin)
Connector A
Connector B
⁄ See next page
Fuse(10A)
Front output
Rear output
Sub Woofer output
To connect the Kenwood navigation system, consult
your navigation manual.
Light Blue/Yellow (Steering
remote control wire)
USBconnector(0.8m)
To USB device ⁄ Do not remove the
cap when you do not
use the USB cable. The
connector will cause
the unit to malfunction
if it gets in touch with
any metallic part of the
vehicle.
Microphone
(Accessory 3)
Microphone input
AUX input (Stereo)
Use the mini-plug which is stereo type
and does not have any resistance.
To use the steering wheel remote control feature, you
need to an exclusive remote adapter (not supplied)
matches your car is required.

71 | KDC-BT92SD English | 72

Accessories/ Installation Procedure

Accessories

1
..........1
2

..........2

3
3 m ..........1

Installation Procedure

1

To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.

2

Make the proper input and output wire
connections for each unit.

3

Connect the wire on the wiring harness.

4

Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.

5

Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.

6

Connect the wiring harness connector to the unit.

7

Install the unit in your car.

8

Reconnect the - terminal of the battery.

9

Press the reset button.
¤
• Mountingandwiringthisproductrequiresskillsand
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
• Makesuretogroundtheunittoanegative12VDCpower
supply.
• Donotinstalltheunitinaspotexposedtodirectsunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
• Donotuseyourownscrews.Useonlythescrewsprovided.
If you use the wrong screws, you could damage the unit.
• IfthepowerisnotturnedON(“Protect”isdisplayed),the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
• Makesurethatallwireconnectionsaresecurelymadeby
inserting jacks until they lock completely.
• Ifyourvehicle’signitiondoesnothaveanACCposition,or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
• Useacommerciallyavailableconversionconnectorifthe
connector does not fit in the vehicle connector.
• Insulateunconnectedwireswithvinyltapeorothersimilar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Iftheconsolehasalid,makesuretoinstalltheunitsothat
the faceplate will not hit the lid when closing and opening.
• Ifthefuseblows,firstmakesurethewiresaren’ttouching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Connectthespeakerwirescorrectlytotheterminalsto
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
• Aftertheunitisinstalled,checkwhetherthebrakelamps,
blinkers, wipers, etc. on the car are working properly.
• Mounttheunitsothatthemountingangleis30°orless.
• Receptionmaydropiftherearemetalobjectsnearthe
Bluetooth antenna.
Bluetooth antenna unit
For Good Reception
To assure good reception, note the following:
•Communicate withthecell-phonewithintheline-
of-sightdistanceof10m(30ft).Thecommunication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
abovemaximumcommunicationrange(10m)is
not always assured.
•A broadcaststationorwalkie-talkielocatednearby
can interfere with communication due to too strong
signal.
Connecting Wires to Terminals