: Select : Adjust
Automatic Search Start
This unit has been preset to STORE brightness This setting does not qualify under ENERGY STAR V4.0. To reduce brightness and energy consumption, change setting to ‘HOME’. This setting does qualify under ENERGY STAR V4.0.
Signal Type
Cable
TV Location
Store
Starting setup
The Starting Setup menu appears the first time you turn on the TV, and assists you to specify the Air/Cable setting, and program your channels automatically.
IMPORTANT: Make sure that the antenna or cable TV system connection is made!
1 To turn on the TV, press POWER (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.).The starting setup function begins.
Auto Setup

2 Press ▲/▼ to select “TV Location”, then press ◀/▶ to select “Store” or “Home”. This product qualifies for ENERGY STAR 4.0 In Home mode default setting.

NOTE:

• This unit has been preset to STORE brightness. This setting does not qualify under ENERGY STAR V4.0.To reduce brightness and energy consumption, change setting to ‘HOME’.This setting does qualify under ENERGY STAR V4.0.

• The device may not conform to the ENERGY STAR 4.0 standard after Reset is performed or the Backlight is adjusted.

3 Press ▲ or ▼ to select “Signal Type”, then press ◀ or ▶ to select “Cable” or “Air”.

4 Press ▲ or ▼ to select “Automatic Search”, then press ▶ or ENTER.

5 Now the “Auto Setup” starts. After the starting setup is completed, the TV channel appears on the screen.

• Depending on the reception condition, it may take from 15 minutes to 30 minutes to complete memorizing digital cable channels. Please be patient.

NOTE:

• If you press ENTER in the process of “Auto Setup”, the Starting Setup stops and changes to the normal screen.

• When you make a menu selection, your changes occur immediately.You do not have to press EXIT/ CANCEL to see your changes.

TV operation

1 To turn on the TV, press POWER. (POWER indicator on the front of the unit changes green. It may take approx. 10 seconds for a picture to appear on screen.)

2 Adjust the volume level by pressing VOL + or – . The volume level will be indicated on the screen by blue bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of blue bars also decreases.

3 Set the Signal Type option to the appropriate

18 position (see “Air/Cable selection” on page 21).

4 Press the Direct Channel Selection (0-9, –) buttons to select the channel.

(If you press only channel number, channel selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2, press 2, then press

ENTER.

10-99: Press the 2 digits in order. Example, to select channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button, followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press ENTER.

• If a channel is selected with only audio content, “Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital signal, “Digital channel signal strength is low” will be displayed on the screen.

The same program may be available on either an analog channel or a digital channel.You may choose to watch either format.

• If a channel is selected to which you have not subscribed, “Digital channel is encrypted” will be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air

 

 

Cable

VHF

 

 

VHF

2-13

 

 

2-13

UHF

14-36

STD/HRC/IRC

14-69

 

(A) (W)

 

37-59

 

(AA) (WW)

 

60-85

 

(AAA) (ZZZ)

 

86-94

 

(86) (94)

 

95-99

 

(A-5) (A-1)

 

100-135

(100) (135)

 

01

 

(4A)

NOTE:

• If a channel with no broadcast is selected, the sound will automatically be muted.

• It may take a few seconds for a digital channel picture to appear on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD TV, such as a VCR player, press INPUT SELECT, then press ▲/▼ or corresponding Number buttons (0-7), then press ENTER.You can select TV, Video1, Video2, Component, HDMI1, HDMI2, PC or DVD depending on which input jacks you used to connect your devices.

Input Select

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.PC

7.DVD

[0-7]:Select

CH /

Press and release CH / . The channel automatically stops at the next channel set into memory.

For proper operation, before selecting channels, they should be set into the memory. See “Memorizing channels” on page 21.