JVC LVT1989-001A Selecting AM Tuner Interval Spacing on the System only, Basic Tuner Operations

Listening to FM and AM Broadcasts

Listening to Other Equipment

Learning More about This System

Selecting AM Tuner Interval Spacing (on the System only)

Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. Before operating the tuner, select the appropriate AM tuner interval spacing used for your area.

• You cannot change the AM tuner interval spacing while the ECO (Ecology) Mode is activated.

1Select AM as the source.

2Turn off (standby) the System.

3		Press and hold to change the AM tuner interval spacing.
	Basic Tuner Operations
	To		Press		Indication/Result
Select FM or AM					Press repeatedly.
					• The selected frequency band appears.
Select a frequency					Press and hold for more than 2 seconds.
					The System starts searching for stations and stops when a station of
				or	sufficient signal strength is tuned in.
					• Press during searching to stop.
					• Press repeatedly to change the frequency step by step.
Tune in to a preset station					Press repeatedly to select its preset number.
• For presetting stations, see
below.				or
Change the FM reception					Press to improve reception.
mode					The (mono) indicator lights up.
(When an FM stereo					Stereo effect will be lost.
broadcast is hard to receive)					To restore the stereo effect, press again. The (stereo) indicator lights up.

Front view

Stereo mini plug cord (not supplied)

1 Turn the volume to minimum.

2Press to select “AUDIO IN.”

3Start playing the connected equipment.

4 Adjust the volume.

Digital Audio Player, etc.

To audio output (or headphone out, etc.)

To Preset the Audio Input Level

If the sound from the equipment connected to the AUDIO IN jack is too loud or too quiet, you can change the audio input level through the AUDIO IN jack (without changing the volume level).

Press repeatedly to select the level as follows:

NORMAL: Ordinary input level.

HIGH: Increases the input level.

Basic and Common Operations (see page 3)

•Pressing one of the source buttons also turns on the System and starts playing back if the source is ready or connected.

•You cannot use the Sound Mode and Sound Turbo at the same time.

Playing Back a Disc/USB Mass Storage Class Device

(see page 4)

•This System cannot play “packet write” discs.

•For MP3/WMA playback...

–In this manual, “file” and “track” are interchangeably used.

–This System can show the Tag data (Version 1).

–MP3/WMA discs are required a longer readout time than regular CDs. (It depends on the complexity of the group/ file configuration.)

–Some MP3/WMA files cannot be played back and will be skipped. This result from their recording processes and conditions.

–When making MP3/WMA discs, use ISO 9660 Level 1 or Level 2 for the disc format.

–This System can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

–It is recommended that you make each MP3/WMA file at a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This System cannot play back files made at a bit rate of less than 64 kbps.

–Playback order of MP3/WMA tracks may be different from the one you have intended while recording. If a folder (group) does not include MP3/WMA tracks, they are ignored.

•Do not use the following USB mass storage class devices...

–Whose rating is other than 5 V and exceeds 500 mA.

–Equipped with special functions such as data security functions.

–Divided by 2 or more partitions.

•For the USB mass storage class device playback...

–When connecting a USB mass storage class device, also refer to its manual.

–Connect one USB mass storage class device to the System at a time. Do not use a USB hub.

–This System is compatible with USB 2.0 Full Speed.

–You can play back MP3/WMA files in a USB mass storage class device (maximum data transfer rate: 2 Mbps).

–You cannot play back a file larger than 2 Gigabytes.

–This System may not play back some USB mass storage class devices and does not support DRM (Digital Rights Management).

•This System can recognize up to 255 groups in a disc. The total number of groups and tracks (in a disc) that can be recognized by the System is 512 (for MP3/WMA).

•This System can recognize up to 99 groups and 999 tracks (with a maximum number of 255 tracks in a group) in a USB mass storage class device.

•Prohibiting disc ejection (or canceling it) is not available when the display is turned off (“DISP OFF”) or the ECO Mode is activated (“ECO ON”) (see page 3).

Setting the Clock and Using Timers (see page 6)

•You cannot set the clock and Daily Timer while the ECO (Ecology) Mode is activated.

•The clock may gain or lose 1 to 2 minutes per month. If this happens, adjust the clock.

•When you unplug the AC power cord or if a power failure occurs, the clock and the timer will be canceled. You need to set the clock first, then the timer again.

Timer Priority:

•If you activate the Sleep Timer after Daily Timer starts playing the selected source, Daily Timer is canceled.

Display Information

	Play mode indicators (See page 4.)		HBS indicator (See page 3.)
		S.TURBO (Sound Turbo)		SOUND indicator
Source indicator		indicator (See page 3.)		(See page 3.)		Source indicators
								FM reception indicators
								(See page 5.)
REC indicator
(See page 6.)								Timer mode indicators
								(See page 6.)
	File type indicators		Main display		A.STBY (Auto Standby)		SLEEP indicator
	(See page 4.)				indicator (See page 6.)		(See page 6.)

Presetting Stations

You can preset 30 FM and 15 AM stations manually.

1Tune in to a station you want to preset.

• You can also store the FM reception mode.

2

3

Press to activate the preset number entry mode.

• Finish the following steps while the indication on the display is flashing.

Press to select a preset number for the station you want to store.

or

4Press to store the station.

5 7

Recording Operations

Setting the Clock and Using Timers

Troubleshooting

Maintenance

Specifications

Before You Start recording

•It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable program and in any literary, dramatic, musical, or artistic work embodied therein.

•The recording level is not affected by the volume.

•Hyper Bass Sound and Sound Turbo (see page 3) do not affect recordings.

•You can record up to 999 tracks per group to the USB mass storage class device. If you try to record a track after recording 999 tracks, “FILEFULL” appears on the display and the track will not be recorded.

•The tracks which are recorded to the USB mass storage class device will be converted into MP3 format (bit rate: 128 kbps).

•You cannot start recording into a USB mass storage class device while “READING” is shown on the display.

•Do not disconnect a USB mass storage class device while playing or recording. It may cause malfunction.

•During recording, the Random Play and Repeat Play will be cancelled.

About SCMS (Serial Copy Management System)

The System uses the Serial Copy Management System which allows only first-generation digital copies to be made of premastered software such as regular CDs.

If you try to record from a duplicated disc into the USB mass storage class device, “SCMS VLT” appears on the display.

1st generation

2nd generation

Recording from a Disc

You can record tracks digitally from a CD onto the USB mass storage class device.

Press to start recording.

(On the System)

ALL REC

READ USB

R01 00:01

Both recording and playback start at the same time.

When playback ends, recording also stops.

•If you have programmed the playing order for CD (see “Programming the Playing Order—Program Play” on page 4), the tracks are recorded in the programmed order if Program Play is activated.

•To stop recording manually, press 7.

To record the playing track

Press to start recording while playing back the track to record.

To erase tracks/groups

You can erase tracks/groups on the USB mass storage class device.

•Once the tracks are erased, you cannot recover them.

•To quit erasing, press 7.

1Select a track/group you want to erase while playback is stopped. (See page 4.)

2

3	Select the target to erase.
	TTL DEL: Delete a track.
	or
	GRP DEL: Delete a group.
	DEL ALL: Delete all tracks.
4

Setting the Clock

Without setting the built-in clock, you cannot use Daily Timer.

• To go back to the previous step, press CANCEL.

1	Press to activate the clock
	setting mode.

00:00

2	or	Adjust the hour, then the
		minute.

Setting the Sleep Timer

Press repeatedly to specify the time (in minutes) as follows:

(canceled)

The SLEEP indicator lights up and the display dims.

To check the remaining time until the System shuts off, press SLEEP once.

Turning Off the System Automatically —Auto Standby function (only for Disc/USB)

Press to activate the Auto Standby.

•The A.STBY indicator lights up.

•The A.STBY indicator starts flashing after playback stops.

If no operation is done for about 3 minutes, the System turns off.

To cancel this function, press the button again.

Setting the Daily Timer

Using Daily Timer, you can wake up with your favorite music.

•You can store three Daily Timer settings; however, you can activate only one of the Daily Timers.

•To correct a misentry during the process, press CANCEL. You can return to the previous step.

1Press repeatedly to select one of the timer you want to set—TIMER-1, TIMER-2, or

TIMER-3.

Canceled

2

31 Adjust the hour then the minute for on-time.

2 Adjust the hour then the minute for off-time.

or 3 Select the playback source—“TUNER FM,” “TUNER AM,” “AUDIO IN,” “DISC,” or “USB HOST.”

4For “TUNER FM” or “TUNER AM”:

Select a preset channel.*

For “DISC” or “USB HOST”: Select a

track. (For MP3/WMA: Select the group, then the track number.)

5Select the volume.

4Turn off the System (on standby).

• When the on-time comes, the System

starts playing the specified source and sets the volume gradually to the preset level.

*If no preset channel is stored, “NOMEMORY” appears. When the on time comes, the System tunes in to the station last tuned in.

To exit from the timer setting, press TIMER as required.

To Turn Off the Daily Timer

1	Press repeatedly to select “TIMER-1,”
	“TIMER-2,” or “TIMER-3.”
2

If you are having a problem with your System, check this list for a possible solution before calling for service.

General

Power does not come on.

\Power plug is not inserted securely. Plug in securely.

Adjustments or settings are suddenly canceled before you finish.

\There is a time limit. Repeat the procedure again.

Operations are disabled.

\The built-in microprocessor may malfunction due to external electrical interference. Unplug the AC power cord and then plug it back in.

Unable to operate the System from the remote control.

\The path between the remote control and the remote sensor on the System is blocked.

\The batteries are exhausted.

No sound is heard.

\Speaker connections are incorrect or loose.

\Headphones are connected.

The System does not work properly.

\Many functions of this System are implemented by microcomputers. If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, and connect the cord again.

Disc/USB Mass Storage Class Device Operations

The disc/USB mass storage class device does not play.

\The disc is placed upside down. Place the disc with the label side up.

\The USB mass storage class device is not connected properly.

MP3/WMA groups and tracks are not played back as you expect.

\Playing order is determined when the groups and tracks were recorded. It depends on the writing application.

The disc/USB mass storage class device sound is discontinuous.

\The disc is scratched or dirty.

\MP3/WMA files have not been properly copied into the USB mass storage class device.

Sounds from USB mass storage class device are interrupted.

\ Noise and static electricity may stop the sound. In this

case, disconnect and connect the USB mass storage class

device again after turning off the System.

Radio Operations

Hard to listen to broadcasts because of noise.

\Antenna connections are incorrect or loose.

\The AM loop antenna is too close to the System.

\The FM antenna is not properly extended and positioned.

\Electrostatic discharge from your body may cause noise. If this happens, turn off and on the System again.

Recording and Editing Operations

Unable to record into the USB device.

\The capacity of the USB device is full. Erase some tracks.

\You have recorded 999 tracks or groups on the USB mass storage class device. Erase unwanted tracks.

\The USB mass storage class device is write-protected.

\The USB mass storage class device you connected is incompatible to this System.

Display Messages for Recording Operations

NODEVICE

•No USB mass storage class device is connected or the connected USB mass storage class device is not compatible with this System.

D. (data) FULL

•The capacity of the USB mass storage class device is full.

FILEFULL

•The USB mass storage class device has exceeded the maximum number of files it can support.

W. (write) PROT

•The USB mass storage class device is write-protected.

SCMS VLT (violation)

•You have tried to copy from a duplicated disc to the USB mass storage class device.

D. (device) FAIL

•The System failed to read the USB mass storage class device.

Timer Operations

Daily Timer does not work.

\The System has been turned on when the on-time comes. Timer starts working only when the System is turned off.

To get the best performance of the System, keep your discs and mechanism clean.

Handling discs

•Remove the disc from its case by holding it at the edge while pressing the center hole lightly.

•Do not touch the shiny surface of the disc, or bend the disc.

•Put the disc back in its case after use.

•Be careful not to scratch the surface of the disc when placing it back in its case.

•Avoid exposure to direct sunlight, temperature extremes, and moisture.

To clean the disc:

•Wipe the disc with a soft cloth in a straight line from center to edge.

Cleaning the System

•Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

•Since the System may deteriorate in quality, become damaged or get its paint peeled off, be careful about the following:

–DO NOT wipe it with a hard cloth.

–DO NOT wipe it strongly.

–DO NOT wipe it with thinner or benzine.

–DO NOT apply any volatile substance such as insecticides to it.

–DO NOT allow any rubber or plastic to remain in contact for a long time.

JVC bears no responsibility for any loss of data in USB mass storage class device while using this System.

Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Amplifier section

OUTPUT POWER:

120 W (60 W + 60 W) at 8 Ω (10% THD)

Speakers/Impedance:	8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “NORMAL”)
Digital input:	250 mV/47 kΩ (at “HIGH”)
	USB REC/PLAY

Tuner section

FM tuning range:	87.50 MHz – 108.00 MHz
AM tuning range:	531 kHz – 1 710 kHz (at 9 kHz
	spacing)
	530 kHz – 1 710 kHz (at 10 kHz
	spacing)

Disc player section

Dynamic range:	80 dB
Signal-to-noise ratio:	85 dB
Wow and flutter:	Immeasurable

USB storage

USB specification:	Compatible with USB 2.0 Full
Compatible device:	Speed
	Mass storage class
Compatible file system:	FAT16, FAT32
Bus power supply:	DC 5 V	500 mA

General

Power requirements:	AC 110 V – 240 V	, 50 Hz/60 Hz
Power consumption:	36 W (power on)
	5 W (standby mode)
Dimensions (approx.):	1 W or less (ECO Mode)
	165 mm x 250 mm x 272 mm
	(W x H x D)
Mass (approx.):	3.5 kg

Speakers

Speaker units:	4 cm cone x 1
Impedance:	12 cm cone x 1
	8 Ω
Dimensions (approx.):	140 mm x 250 mm x 183 mm
	(W x H x D)
Mass (approx.):	1.8 kg each

Specifications and appearance are subject to change without prior notice.

•Do not vibrate the System while recording tracks. It may damage the recorded tracks.

5	DEL NO:	Cancel erasure.
	or	Continue erasure.
	DEL YES:

6

To turn on the Daily Timer again, select one of the timer settings by pressing TIMER, then press SET.

The disc tray does not open or close.

\The AC power cord is not plugged in.

\Disc ejection is prohibited (see page 4).

6 8