JVC 0209RYMMDWDAT dimensions Mises en garde, précautions et indications diverses, Connections

Warnings, Cautions and Others

Mises en garde, précautions et indications diverses

IMPORTANT FOR LASER PRODUCTS

1.	CLASS 1 LASER PRODUCT
2.	CAUTION: Do not open the top cover or cabinet. There
	are no user serviceable parts inside the unit; leave all
	servicing to qualified service personnel.

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1.	Front: No obstructions and open spacing.
2.	Sides/Top/Back: No obstructions should be placed in the

Basic and Common Operations
	The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
	used for the operations.

MICRO COMPONENT SYSTEM

UX-GN6

—Consists of CA-UXGN6 and SP-UXGN5

Thank you for purchasing a JVC product.

INSTRUCTIONS

LVT1989-001A[J/C] 0209RYMMDWDAT

©2009 Victor Company of Japan, Limited

For customer use:

Enter below the Model No. and Serial No. which are

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Le symbole de l’éclair à l’intérieur d’un triangle

3. CAUTION: Visible and/or invisible class 1M laser radiation

when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED

INSIDE THE UNIT.

IMPORTANT POUR PRODUITS LASER

1.PRODUIT LASER CLASSE 1

2.ATTENTION: N’ouvrez pas le couvercle supérieur ni le coffret de l’appareil. Il n’y a aucune pièce réparable par l’utilisateur à l’intérieur de l’appareil; confiez toute réparation à un personnel qualifié.

3.ATTENTION: Rayonnement laser visible et/ou invisible de classe 1M une fois ouvert. Ne pas regarder directement dans le faisceau avec des instruments optiques.

4.REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.

CAUTION

The button in any position does not disconnect the mains line.

Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off).

The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate

air path for ventilation by placing on a stand with a height

of 10 cm or more.

ATTENTION: Aération correcte

Pour prévenir tout risque de décharge électrique ou d’incendie et éviter toute détérioration, installez l’appareil de la manière suivante:

1.Avant: Bien dégagé de tout objet.

2.Côtés/dessus/dessous: Assurez-vous que rien ne bloque les espaces indiqués sur le schéma ci-dessous.

3.Dessous: Posez l’appareil sur une surface plane et horizontale. Veillez à ce que sa ventilation correcte puisse se faire en le plaçant sur un support d’au moins dix centimètres de hauteur.

Front/FaceSide/Côté

CA-UXGN6		CA-UXGN6
SP-UXGN5	SP-UXGN5

CAUTION:

• Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper

Remote sensor STANDBY lamp

PHONES jack

Stereo mini plug cord

Point at the remote sensor on the front panel.

Headphones (not supplied)

		Press
To	Main				Indication/Result
	unit	Remote
Turn on or off			The STANDBY lamp on the System turns off/on.
(standby) the power
Select a source			See “Playing Back a Disc/USB Mass Storage Class Device”
			on page 4.
			See “Listening to an iPod/Viewing Images on the iPod”
			on page 5.
			Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as
			the source.
			• See “Listening				or “Listening
				to FM and AM Broadcasts”
			to Other Equipment” on page 5.
Adjust the volume
						—
Drop the volume in	—		To restore the volume, press again, or adjust the
a moment			volume level.
Select the Sound			Press repeatedly to select the desired Sound Mode.
Mode			The SOUND indicator lights up.

located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.

Serial No.

For U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.

CAUTION:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

1.Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.

2.Ne pas exposer l’appareil à la pluie ni à l’humidité.

•When the System is on standby, the STANDBY lamp lights red.

•When the System is turned on, the STANDBY lamp goes off. The power can be remote controlled.

ATTENTION

La touche , quelle que soit sa position, ne coupe pas la ligne principale.

Débrancher la fiche principale pour couper complètement l’alimentation du secteur (le témoin STANDBY s’éteint).

La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de l’appareil, et l’appareil déconnecté doit être prêt à être utilisé.

•Quand l’appareil est en mode d’attente, le témoin STANDBY est allumé en rouge.

•Quand l’appareil est sous tension, le témoin STANDBY s’éteint. L’alimentation peut être commandée à distance.

CAUTION: Excessive sound pressure from earphones or headphones can cause hearing loss.

ATTENTION: Une pression acoustique excessive des écouteurs ou du casque d’écoute peut entraîner une perte auditive.

CAUTION: Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

ATTENTION: Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du solei, feu, etc.).

or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted

candles, on the apparatus.

• When discarding batteries, environmental problems

must be considered and local rules or laws governing the

disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping

or splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

ATTENTION:

•Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne pas être évacuée correctement de l’appareil.)

•Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil.

•Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement et suivre strictement les règles et les lois locales sur la mise au rebut des piles.

•N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des éclaboussures et ne placez pas des objets remplis de liquide, tels qu’un vase, sur l’appareil.

[European Union only]

[Union européenne seulement]

Display Demonstration

When you plug in the System, the display demonstration automatically starts.

To cancel the display demonstration, press and hold DEMO until “DEMO CLR” is displayed while the System is on standby.

•When the ECO Mode is activated, the display demonstration does not work (and you cannot deactivate it).

•When the display demonstration is activated, it also starts if no operation is done for about 2 minutes while the System is turned on.

Laser Touch Operation

You can use 4/¢ and VOL +/– on the front panel by sliding your finger up or down on the illumination.

To use 4/¢ To use VOL +/–

Using Headphones

Be sure to turn down the volume before connecting or putting on the headphones.

•Connecting the headphones will deactivate the speakers.

•Sound adjustments also affect the sound through the headphones.

Motion Sensor on the Front Panel

When you move your hand close to the front panel while the System is on standby, the controls on the front panel illuminate.

•When no operation is done for about 5 seconds, the illumination turns off.

•When the ECO Mode is activated, the motion sensor does not work.

Touch to turn on the System.

	—
			(canceled)
Emphasize the		The S.TURBO indicator lights up.
sound (Sound		To cancel this function, press again.
Turbo)
Reinforce the bass		The HBS indicator lights up.
sound (Hyper Bass	—	• When Sound Turbo function is activated (see above),
Sound)		the HBS indicator goes off and HBS button does not
		work.
		To cancel this function, press again.
Change the display		Press repeatedly when the System is turned on.
brightness
						(canceled)
Turn off the display		Press repeatedly while the System is on standby.
while on standby
					Clock
		DISP OFF: Turns off the display with the motion sensor
				on.
		ECO ON: Turns on the ECO (Ecology) Mode.
				ECO Mode reduces power consumption
				while the System is on standby by turning
				off the display and motion sensor.

NOTE:

DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start playback.

1

3

Getting Started

Playing Back a Disc/USB Mass Storage Class Device

Supplied Accessories

After unpacking, check to be sure that you have all the

Connections

For iPod

Do not connect the AC power cord until all other connections have been made.

This System can play back...

– CD.

Basic Disc/USB Mass Storage Class Device Operations

Programming the Playing Order—Program Play

following items.

•Remote control, RM-SUXGN6J (× 1)

•Lithium coin battery (× 1: installed in the remote control)

•AM loop antenna (× 1)

•FM antenna (× 1)

•Video cord (× 1)

If anything is missing, consult your dealer immediately.

Prepare the Remote Control

When you use the remote control for the first time, pull out the insulation sheet.

Insulation sheet

To Replace the Battery in the Remote Control

Lithium coin battery (product number: CR2025)

To a wall outlet

Plug the AC power cord only after all connections are complete.

Rear view

To connect the monitor (not supplied)

—To view video/picture from the iPod

Video cord (supplied)

Monitor

To connect the speaker cords

Press and hold

Release Insert

– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files

in ISO 9660 format.

– USB mass storage class device containing MP3/WMA files.

• When playing back an MP3 or WMA track, corresponding indicator lights up.

Loading a Disc (on the System only)

1	Touch to open the disc tray.
2	• When using an 8 cm (3 3/16 inch) disc, place it on
	the inner circle of the disc tray.

3 Touch to close the disc tray.

Connecting a USB Mass Storage Class Device

You can connect a USB mass storage class device such as a USB flash memory device, MP3 player, multimedia card reader, etc. to the System.

To	Press	Indication/Result
Play back the disc		• During playback, press again to pause.
Play back the USB
mass storage class
device
Stop playback		• While playback is stopped, total track number
		and total playing time (for MP3/WMA files,
		group number and track number) appear.
Select a track		Select the next tracks.
		To go back to the beginning of the current or
		previous tracks.
Select a group		Select the next groups.
(MP3/WMA only)
		Select the previous groups.
Forward search/		Press and hold to fast-forward the track during
Reverse search		playback.
		Press and hold to fast-reverse the track during
		playback.
Change		(only for USB)

(only for Disc)

1	Select disc as the source.
2	Activate the Program Play.
3	Select tracks you want for Program Play.
	• For MP3/WMA files only: You can also use UP or

	or	DOWN.
4		Press to store the selected track.

5Repeat steps 3 and 4 to program other tracks you want.

• If you try to program a 33rd track, “PGM FULL” appears.

6	The tracks are played back in the programmed
	order.

Operations for Program Play (while not playing)

• To check the programmed contents, press 4 or ¢.

• To add tracks, repeat steps 3 and 4 above.

• To erase the entire program, press and hold CANCEL for about 2 seconds.

• To exit from Program Play, press PROGRAM or 7.

– The stored program is kept.

NOTES:

•	Store the battery in a place where children cannot reach. If
	a child accidentally swallows the battery, consult a doctor
•	immediately.
	To prevent the battery from overheating, cracking, or starting
	a fire:
	– Do not recharge, short, disassemble or heat the battery or
	dispose of it in a fire.
	– Do not leave the battery with other metallic materials.
	– Wrap the battery with tape and insulate when throwing
	away or saving it.
	– Do not poke the battery with tweezers or similar tools.

		Red	Red
To connect the FM antenna (supplied)	For better FM reception	Black	Black
Extend it so that you can obtain the best reception.	Disconnect the supplied FM antenna, and connect
	to an outdoor FM antenna using a 75 Ω wire with	From right	From left
	coaxial type connector.	speaker	speaker

FM antenna (supplied)	Outdoor FM antenna
	(not supplied)

Front view

USB cable (not	USB memory
supplied)	(not supplied)

or

NOTES:

•	When connecting with a USB cable, use the USB 2.0 cable whose length is less than
•	1 m (3.3 ft).
	USB mass storage class device is charged through the USB terminal when the System
•	is turned on and the source is “USB.”
	You cannot connect a computer to the USB terminal of the System.

the display	Press repeatedly.
information

NOTES:

•If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or “NO USB” appears on the main display.

•If MP3/WMA files are not recorded on the disc or in the USB mass storage class device, “NO PLAY” appears on the main display.

Playing Repeatedly—Repeat Play

1 Press repeatedly to specify the repeat mode as follows:

RPT TRK: Repeats the current (or specified) track. [1]

Playing at Random—Random Play (only for Disc)

1Select disc as the source.

2Press repeatedly to select the desired Random Mode.

RANDOM: Plays all tracks in random order. [ALL RND]

RND GRP: Plays tracks in the current group in random order. (MP3/WMA only). [RND]

RND OFF: Normal playback

• Dispose of battery in the proper manner, according to federal,

state, and local regulations.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

CAUTION:

To assemble the AM loop antenna (supplied)

AM loop antenna (supplied)

To connect the AM loop antenna

Turn the AM loop antenna until the best reception is obtained.

NOTES:

•	Make sure the antenna conductors do not touch any other
	terminals, connecting cords and power cord. Also, keep the
	antennas away from metallic parts of the System, connecting
•	cords, and the AC power cord. This could cause poor reception.
	Keep the AM loop antenna cable wrapped around the AM loop
	antenna frame, otherwise the effectiveness and sensitivity of the
•	AM loop antenna may be reduced.
	Make sure both the speakers are connected correctly and firmly.

•	Do not disconnect the USB mass storage class device when the System is turned on. It
•	may cause malfunction of both this System and the device.
	Noise and static electricity may stop the USB mass storage class device sound. In this
	case, disconnect the USB mass storage class device and connect it again after turning
•	off the System.
	Depending on the shape of USB mass storage class device, the USB terminal may
	not be fully inserted into the USB terminal on the System. In such a case, use a USB
	extension cable (not supplied) to connect.

Prohibiting Disc Ejection (on the System only)

RPT GRP: Repeats all tracks in the current group (MP3/WMA only). []

RPT ALL: Repeats all tracks. [ALL]

RPT OFF: Normal playback

2 or

Operations for Random Play

•To skip a track, press ¢.

•To go back to the beginning of the current track, press 4.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

•	When connecting the speaker cords, match the polarity of the
•	speaker terminals: red color to (+) and black color to (–).
	DO NOT connect more than one speaker to each terminal.
•	DO NOT allow the conductor of the speaker cords to be in touch
	with the metallic parts of the System.

You can lock the disc tray so that no one can eject the loaded disc.

While the System is on standby...

To cancel the prohibition, repeat the same procedure.

2 4