JVC LYT1643-001A Power, Charging The Battery Pack, About Batteries, BATT, WARNING, power indicator, GETTING STARTED, GETTING STARTED EN, To detach the battery pack

		GETTING STARTED EN 13
Power		NOTES:
Charging The Battery Pack		● If the protective cap is attached to the battery
Charging The Battery Pack		pack, remove it ﬁrst.
POWER/CHARGE Lamp		● During charging, the camcorder cannot be
POWER/CHARGE Lamp		operated.
Battery pack		● Charging is not possible if the wrong type of
Battery pack		battery is used.
mount		battery is used.
mount		● When charging the battery pack for the ﬁrst time
		● When charging the battery pack for the ﬁrst time
		or after a long storage period, the POWER/
		CHARGE lamp may not light. In this case,
Arrow	2	remove the battery pack from the camcorder,
	2	then try charging again.
1		● If a fully charged battery pack is attached to the
1		unit, POWER/CHARGE lamp will blink for
Battery		unit, POWER/CHARGE lamp will blink for
Battery		approx. 10 seconds before it turns off.
pack		● If the battery operation time remains extremely
		● If the battery operation time remains extremely
BATT.		short even after having been fully charged, the
		battery is worn out and needs to be replaced.
Power Switch	To DC connector	Please purchase a new one.
		● Since the AC Adapter processes electricity
Lock		internally, it becomes warm during use. Be sure
Lock		to use it only in well-ventilated areas.
Button		to use it only in well-ventilated areas.
Button		● After 5 minutes have elapsed in Record-
		● After 5 minutes have elapsed in Record-
		Standby mode with the cassette inserted and no
		operation is performed, the camcorder will
		automatically turn off its power supplied from the
	AC Adapter	AC adapter. In this case, the battery charge
	AC Adapter	starts if the battery is attached to the camcorder.
To AC outlet		starts if the battery is attached to the camcorder.
To AC outlet		About Batteries
1 Set the Power Switch to “OFF”.		About Batteries
2 With the arrow on the battery pack pointing		DANGER! Do not attempt to take the batteries
upward, push the battery pack slightly against		apart, or expose them to ﬂame or excessive
upward, push the battery pack slightly against		heat, as it may cause a ﬁre or explosion.
the battery pack mount 1.		heat, as it may cause a ﬁre or explosion.
3 Slide up the battery pack until it locks in		WARNING! Do not allow the battery or its
3 Slide up the battery pack until it locks in		terminals to come in contact with metals, as
place 2.		this can result in a short circuit and possibly
4 Plug the AC Adapter into an AC outlet.		this can result in a short circuit and possibly
4 Plug the AC Adapter into an AC outlet.		start a ﬁre.
5 Connect the AC Adapter to the camcorder.		To restore the accuracy of the battery
● The POWER/CHARGE lamp on the camcorder		To restore the accuracy of the battery
● The POWER/CHARGE lamp on the camcorder		power indicator
blinks to indicate charging has started.		power indicator
● When the POWER/CHARGE lamp goes out,		If the battery power indication differs from the
charging is ﬁnished. Unplug the AC Adapter		actual operating time, fully charge the battery,
from the AC outlet. Disconnect the AC Adapter		and then run it down. However this method
from the camcorder.		may not work if the battery was used for a long
To detach the battery pack		period of time under extremely high/low
To detach the battery pack		temperature condition or charged too many
Slide the battery pack downward while		temperature condition or charged too many
Slide the battery pack downward while		times.
pressing BATT. to detach it.		times.
pressing BATT. to detach it.
Battery pack	Charging time
BN-VF808U*	Approx. 1 hr. 30 min.
BN-VF815U	Approx. 2 hrs. 40 min.
BN-VF823U	Approx. 3 hrs. 50 min.
* Provided

GETTING STARTED