INSTALLATION
5.How to Attach the SCSI Cable
If required two SCSI bus channels may be used by adding the provided SCSI cable. If the
1.While holding the two blind plates, remove the four screws on the SCSI connector installa- tion section at the rear of the JVC CD/DVD Library in order to remove the two blind plates.
2.Insert the provided SCSI cable through the installation hole from the back side of the rear panel and secure it with the four screws.
Remove the connector cap of the SCSI cable for installation.
Be sure that the SCSI connector is inserted in the correct direction. (It should be the same as the direction of the SCSI connector
3.If you are not connecting the SCSI cable to the OUT side of the SCSI connector
SCSI cable
Blind plate
Connector cap
ENGLISH
6.How to Connect Cables to the DVD-R Drive
Also refer to the corresponding sections in your Library Instructions Manual.
1. Connect the power supply cable, control cable and SCSI cable to the connectors at the rear of the
When using the
When using the
drive bay to the drive.3
Insert all connectors firmly.
Rear section of the | 1 | 14p | |
Slide switch | N W |
|
|
|
|
| |
|
| 2 | 4p |
| 3 |
|
|
DIP switch
Power cable
Connection example of a SCSI cable
(Terminate here |
| ) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
(Terminate here |
| ) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Library SCSI board |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SCSI cable
Internal SCSI cable (additional)
•Up to two
SCSI connector
|
|
|
|
| OUT 2 |
| Connect an active terminator. | ||
|
|
|
|
| IN | 2 |
| To be connected with host computer's SCSI host adapter No.2 | |
|
|
|
|
| OUT 1 |
| Connect an active terminator. | ||
|
|
|
|
|
| ||||
|
|
|
|
| IN | 1 |
| To be connected with host computer's SCSI host adapter No.1 | |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
Internal SCSI cable (Standard)
•Up to 6 drives can be connected
(• Up to 4 drives in the case of
SCSI cables should be connected as a daisy chain connection. Each connector may be connected to the drive posi- tions as illustrated in the diagram.
Terminate the physical end of the SCSI bus. For information on how to set the
For an external terminator we recommend that an active SCSI terminator is used with the JVC CD/DVD Library.
5