JVC RX-8012VSL manual Selecting the Analog or Digital Input Mode

INPUT ATT

Selecting the Analog or Digital Input

Mode

When you have connected digital source components using the digital terminals (see page 8), you need to change the input mode for these components to the appropriate digital input mode correctly — DGTL AUTO, DGTL DTS, or DGTL D.D.

Before you start, remember...

•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.

On the front panel:

1.Press one of the source selecting button (DVD, TV SOUND/DBS, CD, CDR, or TAPE/MD)* for which

you want to change the input mode.

The lamp on the front panel button for selected source lights up.

DVD MULTI	DVD	VCR 1	VCR 2	VIDEO	TV SOUND/DBS
					SOURCE NAME
PHONO	CD	CDR	TAPE / MD	USB AUDIO	FM / AM

SOURCE NAME

Note:

*Among the source listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting” on page 19.)

2. Press INPUT ANALOG/DIGITAL INPUT

ANALOG/DIGITAL

(INPUT ATT) briefly to change the input mode.

•Each time you press the button, the input mode changes as follows.

DGTL AUTO ANALOG

(Digital)

DGTL AUTO: Select this for the digital input mode. The receiver automatically detects the incoming signal.

ANALOG: Select this for the analog input mode.

ANALOG always lights up.

When selecting “DGTL AUTO,” following indicators showing detected signals light up on the display.

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, “DGTL AUTO” may not work properly and the following symptoms may occur:

•Sound does not come out at the beginning of playback.

•Noise comes out while using the searching or skipping chapters or tracks.

In this case press CONTROL UP 5/	CONTROL
	DOWN UP
DOWN °to select “DGTL D.D” or “DGTL
DTS” while “DGTL AUTO” still remains
on the display.

•Each time you press the button, the input mode changes as follows.

DGTL AUTO DGTL D.D

(Digital)(Digital Dolby Digital)

DGTL DTS

(Digital)

When selecting “DGTL D.D” or “DGTL DTS,” following indicators showing detected signals light up on the display.

: Always lights up.

When selecting “DGTL D.D”

DIGITAL : • Lights up when Dolby Digital signals come in.

•The frame flashes when Dolby Digital signals are not recognized.

When selecting “DGTL DTS”

: • Lights up when DTS Digital Surround signals come in.

•The frame flashes when DTS Digital Surround signals are not recognized.

Note:

When you turn off the power or select another source, “DGTL D.D” and “DGTL DTS” settings are canceled and the digital input mode is automatically reset to “DGTL AUTO.”

To change the input mode back to analog input, select

“ANALOG” in step 2.

From the remote control:

1. Press the source selecting	DVD	DVD MUILTI	CD	FM/AM
button (DVD, CD, TV/DBS, TV/DBS		VIDEO	CDR	PHONO
CDR, or TAPE/MD)* for	VCR 1	VCR 2	TAPE/MD	USB
which you want to change

the input mode.

Note:

*Among the source listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting” on page 19.)

English

LINEAR PCM

DIGITAL

:Always lights up.

:• Lights up when Linear PCM signals come in.

•The frame flashes when detecting signals.

•LINEAR PCM without frame flashes when PCM signals are not recognized.

:Lights up when Dolby Digital signals come in.

:Lights up when DTS Digital Surround signals come in.

2. Press ANALOG/DIGITAL INPUT	ANALOG/DIGITAL
to change the input mode.	INPUT

•Each time you press the button, the input mode changes as follows:

DGTL AUTO ANALOG

(Digital)

When playing a software encoded with the Dolby Digital or

DTS Digital Surround, “DGTL AUTO” may not happen to work well. In this case press CONTROL UP 5/DOWN °on the front panel to select “DGTL D.D” or “DGTL DTS” (while “DGTL AUTO” remains on the display).

Note:

You can select “DGTL D.D” or “DGTL DTS” from the remote control by

using the On-Screen Menus (see page 36).

20