JVC RX-8012VSL manual Adjusting the 3D-PHONIC Modes

English

4.	Press LEVEL +/– to adjust the	+∗BAL L
	speaker output levels (–10 dB to	CH/∗LEVEL
	+10 dB).
		−∗BAL R
5.	Press SOUND.	SOUND
	• To adjust other speaker output levels, repeat
	steps 3 and 4.
6.	Press CTR TONE to select the	CTRTONE
	center tone level you want — for	5
		ENTER

5 CH Stereo mode only.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

To make the dialogue softer, select “CTR TONE 1” or “CTR

TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR

TONE 5.”

3. Adjust the center tone.
		EFFECT	SETT
1)	Press EFFECT repeatedly until “CTR
	TONE” appears on the display.
	The display shows the current setting.
2)	Press CONTROL UP 5/DOWN °	CONTROL
	to select the center tone level you
		DOWN UP

want.

The center tone adjustment affects the mid-frequency range, which the human voice is mostly made up of.

•Each time you press the button, the display changes to show the following:

CTR TONE 1 CTR TONE 2 CTR TONE 3

(Softer)(Soft)(Flat)

CTR TONE 5	CTR TONE 4
(Sharper)	(Sharp)

To make the dialogue softer, select “CTR TONE 1” or

“CTR TONE 2.”

To make the dialogue clearer, select “CTR TONE 4” or “CTR TONE 5.”

When “CTR TONE 3” is selected, no adjustment is applied.

4. Adjust the overall levels of the effect.

When “CTR TONE 3” is selected, no adjustment is applied.

1) Press EFFECT repeatedly until

EFFECT SETT

Adjusting the 3D-PHONIC Modes

Before you start, remember...

•Make sure that you have set the speaker information correctly (see page 17).

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again.

•You cannot adjust the center speaker output level when you have set “CTR SPK” to “NONE.” See page 17.

•To adjust the front speaker output balance and subwoofer output level, see pages 16 and 17.

On the front panel:

1. Press DSP MODE repeatedly until DSP MODE

“3D ACTION” or “3D DIGITAL” appears on the display.

The DSP MODE lamp on the front panel

button lights up, and the 3D-PHONIC and DSP indicators also light up on the display.

“EFFECT” appears on the display.

The display shows the current setting.

2) Press CONTROL UP 5/DOWN °

to select the effect level you want.					CONTROL
				DOWN UP
• Each time you press the button, the
display changes to show the following:
EFFECT 1	EFFECT 2		EFFECT 3
EFFECT 5		EFFECT 4

As the number increases, the selected 3D effect mode becomes stronger. (Normally set it to “EFFECT 3.”)

From the remote control:

1. Press DSP MODE repeatedly until	DSP
“3D ACTION” or “3D DIGITAL”	MODE
appears on the display.

The DSP MODE lamp on the front panel button lights up, and the 3D-PHONIC and DSP indicators also light up on the display.

2. Adjust the center speaker output level.

1)	Press LEVEL ADJUST repeatedly		LEVEL
		L
	until “CENTER” appears on the		ADJUST
	display.
2)	Press CONTROL UP 5/DOWN °to
	adjust the center speaker output level	CONTROL

(from –10 dB to +10 dB). DOWN UP

2. Press SOUND.

The 10 keys are activated for sound adjustments.

3.Press CENTER to select the center speaker.

•“CTR” appears on the remote control display window.

4.Press LEVEL +/– to adjust the center speaker output levels (from –10 dB to +10 dB).

SOUND

∗CENTER

9

+∗BAL L

CH/∗LEVEL

−∗BAL R

SOUND

5. Press SOUND.

33