JVC RX-DP20VBKC manual Compu Link Remote Control System, MD recorder, CD recorder

COMPU LINK Remote Control System

The COMPU LINK remote control system allows you to operate JVC audio components through this receiver.

To use this remote control system, you need to connect JVC audio components through the COMPU LINK (SYNCHRO) jacks (see below) in addition to the connections using cables with RCA pin plugs (see page 11).

•Make sure that the AC power cords of these components are unplugged before connection. Plug the AC power cords only after all connections are complete.

				Cassette deck
				or
				MD recorder
				CD recorder
COMPU	AV	TEXT	IR	CTRL
LINK-4	COMPU COMPU			OUT
			OUT
(SYNCHRO) LINK-		LINK		+12V
			IR	10mA MAX
			IN
				RX-DP20VBK
				CD player
IMPORTANT:

Check the following before or while using the buttons and controls.

Notes:

•There are four versions of COMPU LINK remote control system. This receiver is equipped with the fourth version—COMPU LINK-4. This version is created by adding systematic operations with the CD recorder to the previous version—COMPU LINK-3.

•If your audio component has two COMPU LINK jacks, you can use either one. If it has only one COMPU LINK jack, connect it so that it is the last item in the series of components. (For example, the CD recorder or CD player on the left column.)

•To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 27.)

•Refer also to the manuals supplied for your audio components.

This remote control system allows you to use the four functions listed below.

Remote Control through the Remote Sensor on the Receiver

You can control the connected audio components through the receiver using this remote control. For details, see pages 71 and 72.

Automatic Source Selection

•When you press the play (3) button on a connected component or on its own remote control, the receiver automatically turns on and changes the Zone 1 source to the component.

		DGTL AUTO	SPEAKERS	1
L	R	LINEAR PCM
SUBWFR				VOLUME

dB

For Zone 1 operations:

The ZONE 1 ON/OFF lamp on the unit is lit.

For Zone 2 operations:

The ZONE 2 ON/OFF lamp on the unit is lit.

•When using the unit:

–For the Zone 1 operations: “ZONE 2” is not shown in the main display.

–For the Zone 2 operations: “ZONE 2” is shown in

the main display.	DOOR
	DOWN

–Press DOOR DOWN to use the buttons inside the front door.

To close the front door, press DOOR UP.

•When using the remote control:

When operating the receiver using the remote control, the display on the unit always shows the Zone 1 source information though you are operating it for the Zone 2 source.

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1” or “ZONE 2” correctly.

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

LEARN TRANSMIT		LEARN TRANSMIT
ZONE 1	ZONE 2	ZONE 1	ZONE 2

Ex. When you operate the CD player

–If the receiver is already turned on with the ZONE 2 ON/OFF lamp on the unit lit and the source name for Zone 2 appears on the display, the receiver changes the Zone 2 source to the component.

SPEAKERS 1 ZONE 2

VOLUME

dB

Ex. When you operate the cassette deck

• When you press PLAY on the remote control

supplied for this receiver, the receiver	PLAY
automatically turns on and changes the Zone 1
source or Zone 2 source to the target component,

depending on the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector setting on the remote control.

•When you select a new source on the receiver or on the remote control supplied for this receiver either for Zone 1 or Zone 2, the newly selected component begins playing immediately, and the previously selected source continues playing without sound for a few seconds.

Note:

If the source changes from an analog source, for which Analog Direct (see page 27) is activated, to a digital source, muting time* will be a little longer.

*The period during which the receiver changes the source mechanically. No sound comes out during this period.

61