Manuals / JVC / Home Audio / Stereo System

JVC UX-S57 manual Connecting Speakers, 2Hold the clamp of the speaker terminal

Models: UX-S57

1 32

Download 32 pages 60.88 Kb

Page 10

Getting Started (continued)

Getting Started (continued)

Do not connect the AC power cord until all other connections have been made.

AM (MW) antenna

1

ANTENNA

Vinyl-covered wire

(not supplied)

2

AM (MW) loop antenna

(supplied)

1Connect the AM (MW) loop antenna to the AM LOOP terminals as illustrated.

2Turn the AM (MW) loop antenna until you have the best reception.

Connecting Speakers

To connect speakers

You can connect the speakers using the speaker cords.

1
2	3,4
SPEAKERS
RIGHT	LEFT
Speaker	Speaker
cord	cord
Right speaker	Left speaker

To connect an outdoor AM (MW) antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM (MW) loop antenna must remain connected.

For better reception of both FM and AM (MW)

•Make sure the antenna conductors do not touch any other terminals or connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

1If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off.

2Hold the clamp of the speaker terminal.

3Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: red cord to

ªand black cord to ·.

4Release your finger from the clamp.

IMPORTANT:

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one speaker terminal.

7

Image 10

JVC UX-S57 Connecting Speakers, 2Hold the clamp of the speaker terminal, 3Insert the end of the speaker cord into the

Contents

UX-S57-Consistsof CA-UXS57and SP-UXS57 INSTRUCTIONSMICRO COMPONENT SYSTEM GVT0134-003ABCAUTION Proper Ventilation Warnings, Cautions and OthersIMPORTANT FOR LASER PRODUCTS Front ViewSAFETY INSTRUCTIONS Introduction PrecautionsAbout This Manual Listening to FM and AM MW Broadcasts ContentsPlaying Back Discs on the 5-CDChanger Location of the Buttons and Controls Front PanelDisplay window Display window on the front panelCD ALL Remote Control Location of the Buttons and Controls continuedUnpacking Connecting AntennasGetting Started 1Attach the FM antenna to the FM 75 Ω3Insert the end of the speaker cord into the Connecting Speakers2Hold the clamp of the speaker terminal terminalTo remove the speaker grilles Connecting Other EquipmentPutting the Batteries into the Remote Control To connect audio equipmentOn the remote control ONLY 1 Press CLOCK/TIMER Setting the ClockOn the remote control ONLY CLOCK/TIMERTo turn on the unit, press STANDBY/ON Turning On the PowerOn the remote control ONLY To activate the Auto Standby functionAHB BASS1 AHB BASS2 BASS OFF canceled Adjusting the VolumeOn the remote control Basic and Common Operations continuedpress TREBLE to adjust the treble level Adjusting the Tone1 Press BASS to adjust the bass level or Press BASS to adjust the bass1 Tune in to the station you want to preset Tuning in to a StationPresetting Stations DOWN to select a preset numberPress DISC UP or DISC Tuning in to a Preset Station4 Press SET again On the remote control ONLYSearching for Programs by PTY Codes PTY Search Receiving FM Stations with RDSChanging the RDS Information Press RDS DISPLAYOn the remote control ONLY 1 Press TA/News/Info until the datatype you want flashes on the display How the Enhanced Other Networks function actuallyLoading Discs Playing Back Discs on the 5-CDChangerOn the unit ONLY 1 Load discs into the 5-CDChanger 2 Select a disc to play On the remote controlPlaying Back All the Entire Discs -ContinuousPlay 1 Press 3/8 CD, thenOn the remote control ONLY Playing Back Discs on the 5-CDChanger continuedBasic Disc Operations On the remote control“CD PROGRAM” appears on the Programing the Track Playing Order -ProgramPlayPress PLAY MODE repeatedly until displayProhibiting Disc Ejection Playing at Random-RandomPlayRepeating Tracks or Discs-RepeatPlay 2 Press PLAY MODE repeatedly until1 Press CLOCK/TIMER Using the TimersUsing the Daily Timer 2 Set the on-timeyou want the unitthen press CLOCK/TIMER Using the Timers continuedDOWN to set the volume level press CLOCK/TIMERPress SLEEP Using the Sleep TimerOn the remote control ONLY To clean the disc MaintenanceCleaning the unit General NotesPossible Cause TroubleshootingSymptom ActionAdditional Information Description of the PTY codesAmplifier Section-CA-UXS57 SpecificationsSupplied accessories Tuner2004 VICTOR COMPANY OF JAPAN, LIMITED UX-S57MICRO COMPONENT SYSTEM0304AIMMDWJEM VICTOR COMPANY OF JAPAN, LIMITED