4 Press the UP, DOWN, > or < button within 5 seconds to select the preset number.
UP or > button: Increases the preset number by 1.
DOWN or < button: Decreases the preset number by 1.
•When the > or < button is held down, the preset number changes rapidly.
5Press the SET button within 5 seconds.
“STORED” appears and after 2 seconds, the display returns to the broadcast frequency display.
6Repeat above steps 1 to 5 for each sta- tion you want to store in memory with a
preset number.
To change the preset stations, repeat the same steps as above.
Presetting stations automatically –––
In each band, you can automatically preset 30 FM and 15 AM (MW/LW) stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency.
Receiving FM Stations with
RDS
You can use the RDS (Radio Data System) by using the buttons on the Unit and the Remote Control.
RDS allows FM stations to send additional signals with their regular program signals. For example, the stations send their station names, and information about what type of programs they broadcast, such as sports or music, etc. This Unit can receive the following types of RDS signals:
PS (Program Service):
shows commonly known station names.
PTY (Program Type):
shows types of broadcast programs.
RT (Radio Text):
shows text messages the station sends.
EON (Enhanced Other Networks):
provides the information about the types of the programs sent by other RDS stations.
What information can RDS signals provide?
English
TUNER
BAND
AUTO
PRESET
The display shows RDS signal information that the station sends.
(For more than 2 seconds)
1Select a band by pressing the FM/AM button on the Unit (or the TUNER BAND button on the Remote Control).
2Press the AUTO PRESET button on the Remote Control for more than 2 seconds.
3Repeat steps 1 – 2 for the other band.
■If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers.
CAUTION:
Even if the system is unplugged or if a power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again.
Changing the FM Reception Mode
When you have tuned into an FM stereo broadcast, the STEREO indicator lights up and you can hear stereo effects.
If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose any stereo effect.
Press the FM MODE button on the Remote Control so that the MONO indicator lights up on the display.
FM MODE
STEREO 
MONO
To restore the stereo effect, press the FM MODE button on
the Remote Control so that the MONO indicator goes off.
Showing the RDS signals on the display––––––––––––––––––––––––––––––––
Press the DISPLAY MODE button on the Remote Control while listening to an FM station.
Each time you press the button, the display changes to show information in the following order:
PS 
PTY 
RT 
Frequency
DISPLAY MODE
PS (Program Service):
While searching, “PS” appears, then station name is displayed. “NO PS” appears if no signal is sent.
PTY (Program Type):
While searching, “PTY” appears, then broadcast program type is displayed. “NO PTY” appears if no signal is sent.
RT (Radio Text):
While searching, “RT” appears, then a text message sent by the station is displayed. “NO RT” appears if no signal is sent.
Frequency:
Station frequency
To search for a program using the PTY codes
REMEMBER you must preset FM RDS stations to use the EON function. If not yet done, see page 8.
Notes:
•If searching finishes at once, “PS”, “PTY” and “RT” will not appear on the display.
•If you press the DISPLAY MODE button while listening to an AM (MW/LW) station, the display only shows station frequency.
•RDS is not available for AM (MW/LW) broadcasts and for some FM broadcasts.
9
