Turn on the power
After connections and installations are completed, turn on the power to the unit. When the camera is booting, the [STATUS] indicator lights up orange. It lights up green after booting.
Image Adjustment
Adjust the field angle and the focus while checking the actual image on the monitor.
Note
•Before you touch this camera, be sure to touch the metal surface of the monitor terminal first in order to discharge static electricity.
Otherwise, static electricity may cause the camera to malfunction.
Adjust the field angle and focus
1Remove the lens cover.Press the lens cover marking (either A or B) up and down, release either catch, and then release another catch from this camera.
Note
•Do not forcibly pull the lens cover. If you do so, the fall prevention sheet may be removed.
•When mounting the lens cover, be careful not to pinch the protection sheet.
•Remove the lens cover by pulling it straight, and exercise care not to hit the lens. If the lens is hit, it may be scratched by the lens cover.
2Adjust the direction of the camera.Direct the camera at the target.
Note
•Do not hold the lens section when adjusting the direction of the camera. The lens section may be damaged if you apply force to it.
3Adjust the field angle.Loosen the zoom ring setscrew, and adjust the image size by rotating the zoom ring to the right or left. After completing the adjustment, move the fastening screw toward the direction of the lens (direction of the subject), and tighten the screw accordingly.
4Adjust the focus.1Lift the focusing gear control, release the catch from position C and insert it into position D to disengage the gear.
2Loosen the focusing ring setscrew, and focus the image by rotating the ring to the right or left.
Note
•If you open the gear beyond position D, the gear shaft is released from the bearing (E in the figure) to prevent it from being damaged. In this case, insert the shaft into bearing E (the original position) again and use them.
Finely adjust the focus
[FOCUS ASSIST] button
1 | Press the [FOCUS ASSIST] button. |
| • The camera enters Focus Assist mode, and [STATUS] indicator |
| flashes green and orange alternately. |
| • The image is sharpened with the opening of the aperture. |
2 | Shoot the subject. |
3 | Finely adjust the focus. |
Image Adjustment
Adjust the field angle and the focus while checking the actual image on the monitor.
Note
•Before you touch this camera, be sure to touch the metal surface of the monitor terminal first in order to discharge static electricity.
Otherwise, static electricity may cause the camera to malfunction.
Adjust the direction of the camera
Direct the camera at the target.
Note
•Do not hold the lens section when adjusting the direction of the camera. The lens section may be damaged if you apply force to it.
[STATUS] indicator
Focus ring of lens
Back focusing ring
Focusing ring setscrew
[STATUS] indicator
Focus ring of lens
Adjust the field angle and focus
[FOCUS ASSIST] button
1Shoot the subject and press the [FOCUS ASSIST] button.•The camera enters Focus Assist mode, and [STATUS] indicator flashes green and orange alternately.
2Adjust the focus of the lens.1Loosen the back focus setscrew using a cross slot screwdriver. 2Shoot the fine designs farther than the subject you are shooting.
3Connect the camera to a computer, and open the
•For details about computer settings and methods for connecting the camera to a computer, refer to “Instructions (IP Address Settings)”.
4Select “Lens Type” from the “Lens” page in “Advanced Settings”.
•For details on the lens type, refer to “Instructions (Setting)” on the supplied
5Adjust the back focus.
With a Fixed-Focus Lens
•Set the focus ring of the lens to the ∞ position.
•Rotate the back focusing ring to adjust the focus.
With a Zoom Lens
•Zoom the lens to the tele position, and focus an image by rotating the focus ring of lens.
•Zoom the lens to the wide position, and adjust the focus by rotating the back focusing ring.
6Tighten the back focus setscrews by turning them to securely fix them.
1Turn the lens focus ring to adjust the focus.
2When you finish adjustment, secure the lens focus.
3Press the [FOCUS ASSIST] button to release the Focus Assist mode.
4Connect the camera to a computer, and open the
•For details about computer settings and methods for connecting the camera to a computer, refer to “Instructions (IP Address Settings)”.
5Select “Lens Type” from the “Lens” page in “Advanced Settings”.
•For details on the lens type, refer to “Instructions (Setting)” on the supplied
6Select “Day Focus Adjust” from the “Focus” page in “Advanced Settings”.
•The back focus position is automatically adjusted. Adjust the back focus position to finely adjust the focus.
•For details on back focus, refer to “Instructions (Setting)” on the supplied
Note
•It may be difficult to acquire focus the following places.
–Too bright places.
–Too dark places.
–Places where brightness always flickering; people are passing by
–Places where there is little contrast
–Places where there are repeating
•The focus position can be manually adjusted by using the
Viewer installed on your computer connected to the camera.
(☞ “Instructions (Setting)”) Resort to this method if it is difficult to acquire focus automatically.
•If you have changed the lens after performing automatic focus adjustment, initialize the back focus position via the "Focus" page, and perform focus adjustment again from step 1.
•If you experience difficulty with automatic focusing, select "Manual Focus" from the "Focus" page, and manually adjust the focus to the optimal position.
•When using a zoom lens, focus the lens, and then select "Manual Focus" to perform focus adjustment for the zoom range.
Return the catch to C from D in the diagram, and rotate the focus adjustment gear knob to adjust the focus to the optimum position.
4Fix the focusing ring.Hold and press the focus adjustment gear between your fingers in the arrow direction of the figure, and tighten screw of focus adjusting ring.
5Release the Focus Assist mode.•When you release the Focus Assist mode by pressing the [FOCUS ASSIST] button, the [STATUS] indicator lights in green.
•Mount the lens cover.
Mount the lens cover
1Mount the lens cover.Note
•Mount the lens cover carefully to avoid hitting the lens. If the lens is hit, it may be scratched by the lens cover.
•Mount the lens cover securely.
2Remove the protection sheet.Protection sheet
Catches | Knob |
| |
|
|
| |
| D | Focus adjustment gear | |
| C |
|
|
|
| E |
|
| Focusing ring |
|
|
|
|
| A |
|
| Zoom adjustment | B |
|
| ring |
|
|
|
| Lens cover |
[STATUS] |
|
|
|
indicator |
|
|
|
Fall prevention sheet
☞ Continued overleaf 3