SPLASH PROOF AM/FM Radio with CD Player | V10M10_IM_EN_08132007 |
OPERATIONAL INSTRUCTIONS
Tips for Getting Better Reception
1.This unit has the
2.To get better AM radio reception, be sure to place the unit horizontally and reposition it if there are noises on the AM station.
Cleaning the Unit
1.To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
2.The finish on the unit may be cleaned with a dust cloth and cared for as other furniture, Use caution when cleaning and wiping the plastic parts.
3.If the cabinets become dusty, wipe them with a soft dry dust cloth. Do not use any wax or polish sprays on the cabinets.
4.If the front panel becomes dirty or smudged with fingerprints, it may be cleaned with a soft cloth slightly dampened with a mild soap and water solution. Never use abrasive cloths or polishes as these will damage the finish of your unit.
Caution: never allow any water or other liquids to get inside the unit while cleaning.
Cleaning the Disc
1.Treat the disc carefully. Handle the disc only by its edges. Never allow your fingers to contact with the shiny, unprinted side of the disc.
2.Do not attach adhesive tape, stickers etc., to the disc label.
3.Clean the disc periodically with soft,
4.If disc skips or gets stuck on a section of the disc, it is probably dirty or damaged (scratched).
5.When cleaning the disc, wipe in straight lines from the centre of the disc to the edge of the disc. Never wipe in circular motions.
6.To remove a disc from its storage case, press down on the centre of the case and lift the disc outs, holding it carefully by the edges.
7.Fingerprints and dust should be carefully wiped off the disc's recorded surface with a soft cloth. Unlike conventional records. compact disc have no groove to collect dust and microscopic debris, so gently wiping with a soft cloth should remove most particles.
Note: Do not use solvents such as benzine petrol, thinner, commercially available cleaners or
9 | www.jWIN.com |
SPLASH PROOF AM/FM Radio with CD Player | V10M10_IM_EN_08132007 |
USER SAFETY GUIDE
IMPORTANT SAFETY INSTRUCTIONS – CONTINUED
11.SERVICING - The user should not attempt to service the appliance beyond that described in the user's operating instructions. All other servicing should be referred to qualified service professional.
12.BATTERY USAGE – To prevent battery leakage, which may result in bodily injury, property damage or damage to the unit, follow these instructions:
a.Install all batteries correctly according to the polarity (+
b.Do not mix old and new batteries, carbon and alkaline, etc.
c.Remove batteries from the unit when the device will not be used for an extended period of time.
13.LEAD AND MERCURY - This product may contain lead and/or mercury. Disposal of these materials may be regulated by your local authorities due to environmental considerations. For more detailed disposal or recycling information, please contact your local authorities or the EIA (Electronic Industries Alliance) – http://www.eiae.org
IMPORTANT NOTES
1.Do not attempt to clean the unit with chemical solvents as this might damage the finish. Use a clean, dry cloth.
2.Keep this manual in a safe place for future reference.
You can help to protect the environment!
Please remember to respect the local regulations: Hand in the
TO A USER IN USA
This equipment has been tested and found to comply with the limits for a Radio Receiver, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-If necessary, consult the dealer or an experienced radio / TV technician for additional suggestions.
2 | www.jWIN.com |
