KAMERA WERK DRESDEN GmbH

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Removing the film (NOBLEX PRO 150)

1.Turn the camera off at the ON/OFF switch (10).

2.Advance the winding disk (5) until the counter (5a) reaches position »S« and the start button (5b) moves out of the camera housing. Turn the film advance knob at least 4 times to avoid unintentional incidence of light.

3.Unlock the camera back (9) and open it.

4.Press the film spool down until it can be swung out and removed.

Please note Do not change the film under a strong light source.

Inserting the film (NOBLEX PRO 175)

1.Turn the camera off at the ON/OFF switch (10).

2.Advance the winding disk (5) until the counter (5a) reaches position »S«. (If necessary, press the shutter release button (4) to advance to the position »S«.)

3.Unlock the camera back (9) and open it.

4.Insert the film spool into the left-hand compartment (14) in the camera back.

5. Push the tongue of the paper lead under the pressure roll (15).

6.Push the tongue of the paper lead under the fight diversion roller (17) - it is located in the fight-hand compartment behind the take-up spool (18) - and pull it until the double arrow on the protective paper of the film reaches the pressure roller (15).

7.Insert the take-up spool into the right-hand compartment (18).

8.Thread the tongue of the paper lead into the empty spool.

9.Turn the winding disk (5) until the double arrow on the protective paper of the film is opposite the red dot on the camera film guide (16). Make sure that the film is wound snug onto the take up spool.

10.Close the camera back and at the same time press the left diversion roller (19) slightly to the back.

11.Lock the camera back (9).

12.Press the start button (5b). The counter is released with that. Remark: At older models the start key (5b) isn't available yet. In this case the shutter release button (4) has to be pushed.

13.Advance the winding disk (5) in the

direction of the arrow until it stops. The film counter should be at the number 1. To take a picture turn the camera on at the ON/OFF switch (10) and press the shutter release button (4).

Removing the film (NOBLEX PRO 175)

1.Turn the camera off at the ON/OFF switch (10).

2.Advance the winding disk (5) until the counter (5a) reaches position »S« and the start button (5b) moves out of the camera housing. Turn the film advance knob at least 4 times to avoid unintentional incidence of light.

3.Unlock the camera back (9) and open it.

4.Press the film spool down until it can be swung out and removed.

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Page 7 of 15