Karcher 35HD page 2.24

page 2.24

2. Installation Digital Projection LIGHTNING 35HD User Manual

5V@1A fused

auxilliary power

outputs

Auxilliary Power Output (Stage 2 models only)

Two auxilliary power outputs are available, for powering line drivers etc.

Notes

Should the 5V auxilliary output

become overloaded, a resetable

fuse will operate. To reset the

fuse, disconnect from the

auxilliary output for a short

period, then reconnect.

Contents

Main Declaration of Conformity page i Digital Projection LIGHTNING 35HD User Manual Important Information Symbols used in this guide Warnings Important Information page ii Important Information Digital Projection LIGHTNING 35HD User Manual General precautions page iii Digital Projection LIGHTNING 35HD User Manual Important Information Installation precautions page iv Important Information Digital Projection LIGHTNING 35HD User Manual Operation and configuration precautions Compliance with international standards Noise GSGC Acoustic Noise Information Ordinance RF Interference LIGHTNING 35HD User Manual CONTENTS Important Information i 1. Introduction 1.1 2. Installation 2.1 3. Getting started 3.1 4. Using the Menus 4.1 5. Maintenance 5.1 6. Appendix 6.1 Page 1. Introduction page 1.2 Whats in the box? page 1.3 Digital Projection LIGHTNING 35HD User Manual 1. Introduction Key features of the projector page 1.4 Getting to know the projector Chassis lamp, lens and filter Lamp-hours meter page 1.6 Rear panel connection and control Rigging frame 2. Installation page 2.2 Screen requirements Aspect ratio Fitting the image to the DMD Diagonal screen sizes page 2.3 Fitting the image to the screen page 2.4 Positioning the screen and projector page 2.5 Choosing a lens Method one: using the lens charts Method two: by calculation page 2.6 Lens charts Full width image, including native resolution 2048x1080, and 2.35:1 page 2.7 16:9 full height image page 2.8 4:3 full height image page 2.9 5:4 full height image page 2.10 5:4 un-resized image page 2.11 4:3 un-resized image page 2.12 Method two: Choosing a lens by calculation page 2.13 Useful lens calculations page 2.14 Shifting the image 400 256 0.37H 0.125W 540 365 0.5H 0.178W 282 172 0.26H 0.085W page 2.15 Fitting the lens page 2.16 Mounting the projector Levelling Coarse frame adjustment Fine frame adjustment Chassis adjustment Stacking projectors page 2.18 Connecting the projector Digilink page 2.19 Digital Projection LIGHTNING 35HD User Manual 2. Installation Input Formats page 2.20 EDID handshaking Example: setting up the MMS 1000 multimedia switcher Projector Outputs page 2.21 Input connection examples examples page 2.22 Control connection examples LAN connection page 2.23 Power connections USA power input Rest of World power input page 2.24 Auxilliary Power Output (Stage 2 models only) 3. Getting started page 3.2 Using the touch screen Switching the power on page 3.3 Digital Projection LIGHTNING 35HD User Manual 3. Getting started Switching the lamp on Adjusting the lamp power page 3.4 Selecting an image source Adjusting the projected image page 3.5 Digital Projection LIGHTNING 35HD User Manual 3. Getting started page 3.6 Switching the power off 4. Using the Menus Page page 4.3 page 4.4 Introduction page 4.5 Menu structure page 4.6 Show mode Lamp status Video source Main menu Page page 4.8 Lamp menu Lamp power Lamp on Lamp off Lamp menu Lamp/Lens memories Store Recall Advanced menu page 4.10 Lens menu Shift, zoom and focus Centre Calibration Stop all movement Page page 4.12 Image menu Test Patterns Image menu page 4.13 page 4.14 Contrast Contrast page 4.15 Brightness Brightness page 4.16 Gamma Gamma page 4.17 User Gamma Presets Advanced Gamma Setup page 4.18 Advanced image setup Input window Input preset Input pan Advanced image setup page 4.19 page 4.20 Image position Advanced image setup... Image position page 4.21 Image orientation page 4.22 Source menu Source select Single DVI-D (Stage 1 model): Single DVI-D (Stage 2 model only): Dual DVI-D (Stage 2 model only): Configuration menu Detailed status Config menu page 4.24 Networking configuration Ethernet configuration choices Network configuration... Ethernet #1 or #2 page 4.25 Setting the Ethernet port for DHCP or Manual Making the IP address and other settings page 4.26 Wireless LAN configuration Config menu... Network configuration... Wireless LAN page 4.27 Touchscreen calibration Reset IP addresses page 4.28 Engineering & Maintenance menu Log files Software update Engineering & Maintenance menu page 4.29 Help menu Help menu Page Page page 5.2 5. Maintenance Digital Projection LIGHTNING 35HD User Manual Changing the lamp Lamp-hours meter page 5.4 5. Maintenance Digital Projection LIGHTNING 35HD User Manual page 5.5 Digital Projection LIGHTNING 35HD User Manual 5. Maintenance Changing the filter Cleaning the projector and lens 6. Appendix page 6.2 Troubleshooting Problem Possible solutions page 6.3 Problem Possible solutions page 6.4 Specifications Part numbers Optical Electrical Page page 6.6 Lens Data page 6.7 page 6.8 Connections DVI-D connection page 6.9 LAN connection 10BaseT Unshielded Twisted Pair cable Crossed cable page 6.10 Serial control input Null-modem cable Modem settings page 6.11 Using Windows Hyperterminal to connect to the projector page 6.12 Remote communications protocol Version 1.2 Patch A Image commands Image Brightness page 6.13 Image Contrast Image Projection Mode page 6.14 Image Orientation Image Mirror Park page 6.15 Image Colour Temperature Gain Input Image Size page 6.16 Input Image Window Size Image Position page 6.17 Input Capture Offset page 6.18 Test Patterns page 6.19 Degamma Table Select page 6.20 Picture Mute page 6.21 Lens Commands Lens Stop All Lens Move page 6.22 Lens Goto Absolute Position Lens Goto Centre Lens Calibrate Zoom page 6.23 PSU Commands Lamp On Lamp Off page 6.24 Lamp Power