Karcher G 2301 LT, G 2301 LT, K 2301 Shutting Down & Clean-Up, Winterizing And Long-Termstorage

SHUTTING DOWN & CLEAN-UP

Step 1 Remove	Step 2	Step 3	Step 4
detergent suction tube	Turn off the	Turn off the water	Press trigger to
from container and insert	engine.	source.	release water
into one gallon of fresh			pressure.
water. Siphon water at low
pressure for one minute.

7

Step 5 Disconnect	Step 6 Disconnect the high pressure hose from the
the garden hose from the	high pressure outlet and engage the gun safety lock.
water inlet on the unit.

TAKING A BREAK... five minutes or more
Step 1 Turn off the	Step 2 Press trigger	Step 3 Engage gun
engine.	to release water pressure.	safety lock.

WINTERIZING AND LONG-TERM STORAGE

CLEANING TIPS

Deck Cleaning

(with or without detergent)

Pre-rinse deck and surrounding area with fresh water. If using Kärcher Deck and Patio Cleaner, place detergent suction tube direct- ly into cleaning solution and apply to surface at low pressure. For best results, limit your work area to smaller sections of approxi- mately 25 square feet. Allow Kärcher Deck and Patio Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a long sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right. When moving on to a new section of the cleaning surface, be sure to overlap the previous section to eliminate stop marks and ensure a more even clean- ing result.

House Siding

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Kärcher House or Window and Siding Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area

to sections of approximately 6 feet and always apply detergent from bottom to top). Allow Kärcher House or Window and Siding Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface, if surface appears to be drying, simply wet down surface with fresh water. If needed, use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approxi- mately 6 inches from the cleaning surface.

Cement Patios,

Brick and Stone

(with or without detergent)

Pre-rinse cleaning surface with fresh water. If using Kärcher Deck and Patio or All Purpose Cleaner, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. For best results, limit your work area to smaller sec- tions of approximately 25 square feet. Allow Kärcher Deck and Patio or All Purpose Cleaner to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. Rinse at high pressure in a sweeping motion keeping the spray nozzle approximately 3-6 inches from the cleaning surface. Always clean from top to bottom and from left to right.

Cars, Boats & Motorcycles

(with or without detergent)

Pre-rinse vehicle with fresh water. If

using Kärcher Vehicle or All Purpose8 Cleaner, place detergent suction tube direct-

ly into cleaning solution and apply to surface at low pressure. For best results, clean one side of vehicle at a time and always apply detergent from bottom to

top, do not allow detergent to dry on sur- face. If needed, use special Wash Brush Attachment to remove stubborn dirt. Rinse at high pressure in a sweeping motion keep- ing the spray nozzle approximately

6-8 inches from the cleaning surface (dis- tance should increase when rinsing pin- striping or other sensitive surfaces). Always clean from top to bottom and from left to right. For best results, wipe surface dry with a chamois or soft dry cloth.

1.Disconnect all water connections.

2.Start the machine for a few seconds, until the water which had remained in the pump exits. Turn off immediately.

3.Drain the gas and oil from the engine.

4.Do not allow high pressure hose to become kinked.

5.Store the machine and accessories in a room which does not reach freezing temperatures. The machine should not be

placed near an open flame i.e. furnace, hot water heater etc.

Caution: Failure to follow the above direc- tions will result in damage to the pump assembly and accessories.