Kenmore 153.333445, 153.333345, 153.333545 For Your Safety Read Before Lighting, GAS Control

FOR YOUR SAFETY READ BEFORE LIGHTING

explosion may result causing property damage, personal injury or loss of life.

BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING small all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS: DOnot try to light any appliance.

Do not touch any electric switch; do not use any phone inyour building.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier'sinstructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. Ifthe knob will not push in or turn by hand, don'ttry to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

GAB CONTROL KNOB

FIGURE "A"	FIGURE "B"	FIGURE "C"	MAIN BURNER
			/

IGNITOR

_ENERATOR

pIEZO

"OFF POSITION "PILOT" POSITION "ON" POSITION

THERMOSTAT

DIAL

TOPKNOB

GAS CONTROL

1.(_ STOP! Read the safety information above on this label.

2.Set the thermostat to lowest setting (PILOT SETTING). Turn thermostat dial fully clockwise t'_ until it stops.

3.Push thegas control knobdown slightlyand turn clockwise

f'_ to"OFF", SEE FIGURE "A".

NOTE: Knob CANNOT be turned from "PILOT" to "OFF" unless it is pushed down slightly. Do not force.

4.Remove the outer burner door located below the gas control.

5.Wait five (5) minutes to clear out any gas. If you then

smell gas, _) STOP! Follow"B"in the safety information above on this label. Ifyou don'tsmell gas, go to next step.

6.This unit is equipped with a push button pilot ignitor, which is used to light the pilot. Locate the ignitor on the gas control.

7.Turn gas centre] knob counterclockwise _ to"PILOT", SEE FIGURE "B".

8.The pilot is located on the right side of the burner. It can be located by looking through the glass view port while pressing the piezo ignitor button several times. Look for a spark at the pilot location, FIGURE"D".

FIGURE "D"

9.Once the pilot has been found, push the gas knob all the way down. Immediately press the pilot ignitor button rapidly

(4)to (5) times. If the pilot will not light, repeat step (3) through (9).

10.Continue to hold the gas control knob down for about one

(1)minute after the pilot is lit. Release the gas control knob and it will pop back up. Pilot should remain lit.If itgoes out, repeat step (3) through (9). It may take several minutes for air to clear the lines before the pilotwill light.

If knob does not pop up when released, stop and immediatelycall your service technician or gas supplier. If the pilot will not stay lit after several tries, turn the gas

control knob clockwise f_ to "OFF" and call your service technician orgas supplier. SEE FIGURE "A".

11.Once the pilot flame is established replace the outer burner door.

12.At arms length away, turn gas control knob counterclockwise _ to"ON". SEE FIGURE "C".

13.Set thermostat to desired setting.

scald injury. Consult the instruction manual

DANGER: Hotter water increases the risk of before changing temperature.

TO TURN OFF GAS TO APPLIANCE

I'L Set thermostat to the lowest setting (PILOT LIGHTING).	2	•	Push gas control knob down shghgy and turn clockwise
			"	'

/'_ to"OFF". Do not force. SEE FIGURE "A".

18