Kenmore 790.428 manual induction, Cooktop, LED Messages or Light Indicators, Displayed

induction	Cooktop		Display			Messages
LED Messages or Light Indicators				Displayed by Main Contro_
		CONTROLS LOCK ° This feature allows the cooktop to be UockedonUywhen the cooktop is
		switched to OFR Touch and hoUdthe LOCK key pad for 5 seconds. A beep wHUsound and the
		Lock indicator Hght wHUgUow(Fig. 5). Once Uocked,no other dispUayswHUgUowand no Cooking
		Zones wHUactivate. To turn the ControUsLock OFF, touch and hoUdthe LOCK key pad for 5
		seconds. A beep wHUsound, the Lock indicator HghtwHUturn OFF (Fig. 4) and the cooktop may
Fig,4	Fig.5	be used normally			(See p. 11 for more
		COOKTOP POWER - The Cooktop POWER key pad activates the entire Cooktop. To power
		the cooktop, touch and hold the POWER key pad for 2 seconds. A beep will sound and the
		Power LED will glow (See Fig. 7). The cooktop will be in a ready mode for 10 seconds. If no
Fig, 8	Fig. 7	other key pads are touched the Cooktop Main POWER will turn OFF automatically.							To turn the
		Main Power OFF touch and hold the Main POWER key pad for 1 second. A beep will sound
		and the Power Indicator Light will turn OFF (See Fig. 6).
		Errors Codes EO0thru Ell =The control displays Ein Cooking Zones LEDs (Fig. 8) and digits
		in Main Control LED (Fig. 9) together showing an error code. For sen'ice call 1-800-4-MY-
Fig. 8	Fig. 9	HOME@ (See back cover of this manual).
		LED	Messages		or	Light Indicators	Displayed	by Cooking Zone	Controls
		COOKING ZONE ON/OFF PAD - Each of the four Cooking Zones have separate ON/OFF key
		pads. Once the Main Power key pad has been touched to activate the cooktop, touch the
		corresponding Cooking Zone ON/OFF key pad once to active the Cooking Zone needed. 0 will
Fig, lO	Fig, ll	appear	in the LED display. If the corresponding				UP/DOWN	Arrow key pad is not touched within
		5 seconds, the request to turn the Cooking Zone ON will cancel and the Cooktop Main Power
		will turn OFF. To set a Cooking Zone power level touch the corresponding Cooking Zone UP or
		DOWN Arrow key pad once. The Cooking Zone ON/OFF Indicator Light will glow (Fig. 11). To
		turn OFF a Cooking Zone, touch the Cooking Zone ON/OFF key pad once. The Cooking Zone
		Indicator Light will turn OFF (Fig. 10).

Fig. 12

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig,13

POWER LEVEL SETTINGS - The Cooking Zones have four separate Power Level LEDs. Once active, the Cooking Zones will provide 15 Power Levels to choose from. These include I (Fig. 12), 8, 3, _, 5, 5, ?, 8, 9; including precise half-increment Cooking Zone Power Levels of 2. (2.5), 3. (3.5), ft. (4.5), 5. (5.5) and 5. (6.5; See Fig. 14). The highest setting of Por"Power Boost" provides 125% power level for 10 minutes (See Fig. 13). Each key pad touch (or just holding down the Power Level key pad) will scroll through all the available power levels for any Cooking Zone quickly (See pages 9-11 for complete instructions).

RESIDUAL HEAT - Once any Cooking Zone has been used for cooking and turned OFF, and if the cooktop surface temperature on any of the Cooking Zones is still too HOT, H (See Fig, 15) will appear in the LED display for the affected Cooking Zone, The H will continue to display if the temperature is still too HOT,

The Cooking Zones may appear to be cool while turned ON and after they have been turned OFF, The gJass surface may be HOT from residual heat transfered from the cookware and burns may

Occur,

KEEP WARM - Use the WARM (or LOW) key pad to activate the Warm setting for any of the Cooking Zones. The ON/OFF key pad for the desired Cooking Zone must be activated first, then touch the WARM key pad located in the Cooktop Main Control area once to set. L (LOW) should appear in the corresponding Cooking Zone LED (See Fig. 16 & page 10 for complete information).

PAN DETECTION - Aii four Cooking Zones wiii provide a Pan Detection message, if a Cooking Zone is turned ON and no pan is detected for the Cooking Zone, the pan has been moved or if the pan is not centered correctly or if the pan is not made of magnetic material, F(See Fig, 17) will appear in the affected Cooking Zone LED display,