Kenmore 795.7977 HOW TO REMOVE DOOR HANDLES

NOTE:Itis ALWAYSrecommendedtoremovetherefrigeratordoorswhenitis necessarytomovetherefrigeratorthroughanarrowopening.Ifnecessary,followthedirectionsbelowtoremovethedoorhandles.

HOW TO REMOVE DOOR HANDLES

NOTE: Handle appearance may vary from

illustrations on this page.

1. Removing Refrigerator Handle

•Loosen the set screws with a 2.5 mm

(3/32") Allen wrench and remove the

handle.

NOTE: If the handle mounting fasteners

need to be tightened or removed, use a

1/4" Allen wrench.

Set Screw

Mounting

Fasteners

Allen

Wrench

2. Removing Freezer Drawer Handle

• Loosen the set screws located on the

lower side of the handle with a 3.1 mm

(1/8") Allen wrench and remove the

handle.

NOTE: If the handle mounting fasteners

need to be tightened or removed, use a

1/4" Allen wrench.

Contents

Main mmtrio Page BOTTOM FREEZER REFRIGERATOR WARRANTY f J Master Protection Agreements BASIC SAFETY PRECAUTIONS SAVE THESE INSTRUCTIONS BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER IMPORTANT: Please read carefully. TO CONNECT ELECTRICITY RECOMMENDED GROUNDING METHOD USE OF EXTENSION CORDS Page UNPACKING YOUR REFRIGERATOR INSTALLATION NEXT HOW TO REMOVE DOOR HANDLES HOW TO REPLACE DOOR HANDLES REMOVING AND REPLACING REFRIGERATOR DOORS ACAUTION Collet Page Page HOW TO REMOVE AND REINSTALL THE PULLOUT DRAWER Page LEVELING AND DOOR ALIGNMENT L..... \ l / /X SETTING THE CONTROLS Page IN-DOOR ICE BANK ADJUSTING CONTROL SETTINGS FOOD STORAGE GUIDE STORING FROZEN FOOD REFRIGERATOR SECTION WATER DISPENSER REFRIGERATOR SHELVES HUMIDITY CONTROLLED CRISPER REMOVING HUMIDITY CONTROLLED CRISPER TEMPERATURE CONTROLLED PANTRY DRAWER MODULAR DOOR BIN DAIRY BIN FREEZER SECTION EXTRA ICE BIN DURABASE DIVIDER DURABASE AIRFLOW FILTER Performance Data Sheet For Model 5231JA2006A-S Using Replacement Cartridge 5231JA2006A GENERAL CLEANING TIPS OUTSIDE INSIDE WALLS (allow freezer to warm up so cloth won't stick) DOOR LINERS AND GASKETS "' t\ POWER INTERRUPTIONS WHEN YOU GO ON VACATION WHEN YOU MOVE AUTOMATIC ICEMAKER ,& CAUTIONS WHEN YOU SHOULD SET THE ICEMAKER POWER SWITCH TO O (OFF) NORMAL SOUNDS YOU MAY HEAR PREPARING FOR VACATION BEFORE YOU BEGIN WHAT YOU WILL NEED INSTALLATION INSTRUCTIONS 1. SHUT OFF THE MAIN WATER SUPPLY 2. CHOOSE THE VALVE LOCATION 3. DRILL THE HOLE FOR THE VALVE INSTALLATION INSTRUCTIONS (CONTINUED) ./ 8. FLUSH OUT THE TUBING 6. ROUTE THE TUBING 9. CONNECT THE TUBING TO THE REFRIGERATOR 1/4" \ / l 10. TURN THE WATER ON AT THE SHUTOFF VALVE 11. PLUG IN THE REFRIGERATOR 12. START THE ICEMAKER UNDERSTANDING SOUNDS YOU MAY HEAR REFRIGERATOR DOES NOT OPERATE LIGHTS DO NOT WORK VIBRATION OR RATTLING NOISE COMPRESSOR MOTOR SEEMS TO RUN TOO MUCH DOORS WILL NOT CLOSE COMPLETELY FROST OR ICE CRYSTALS ON FROZEN FOOD ICE HAS OFF-TASTE OR ODOR THERE IS WATER IN THE DEFROST DRAIN PAN THE REFRIGERATOR SEEMS TO MAKE TOO MUCH NOISE THE ICEMAKER IS NOT PRODUCING ICE OR ICE CUBES ARE FREEZING TOO SLOWLY CUBES PRODUCED BY ICEMAKER ARE TOO SMALL THE DOORS ARE DIFFICULT TO OPEN TEMPERATURE IS TOO WARM OR THERE IS INTERIOR MOISTURE BUILDUP Page Your Home anage 1-800-4-MY-HOME (1-8o0-_69-_663) Our Home 1 800 488 1222 (U.S.A.) 1 800 469 4663 (Canada)