Kenmore 85501, 85500 manual and turn on the unit

Foryourconvenience, all three filters (Pro- Filter, Washable Nano-Silver/CarloonFilter, and True HEPA Filter) come in one pre-

6. Plug in the power cord to a we1outlet

and turn on the unit,

6. Do not dry the two _ters--running the	8, Replace the filter ¢_ssette and front
unit will be sufficient to drythem.	panel as described in Replacement
	Procedure.

packaged replacement cassette.

For optimum unit efficiency, wash the Pre- Filter and Washable Nano-Silver/Carbon

Filter as described below (Filter Cleaning) every three months.

Do not wash and reuse the True HEPA

Fitter_tt will not work effectively.

WARNING: Before replacing or cleaning t any filters, make sure to remove the powerplug from the wa out et.

7. To turn off the CHANGE FILTER

INDICATOR, press the FUNCTION and

OFF ]IMER buttons at the same time for

five seconds; the CHANGE FILTER

INDICATOR will flash five times and turnoff.

Filter Cleaning

we recommend cleaning the Pro-Fitter (A)

and tile Nano_Silver/CarbonFilter (C) every three monthswith normal use, The interval

between cleanings will vary based on room conditions.

7.Replace each filter in the cassette frame by insertingone tong edge first, then

snapping intoplace by pushing sideways and down at the same time. Make sure

both fittersare completelyinside the cassette frame and secured by the short tabs. If a filter Is on top of one or more tabs, pulloutward,slightly flexing the

cassette frame, while gently pushing down on the edge of {he filter,

gPlug in the power card to a wall outtet and turn on the unit.

Note: Neveratlem!_to removetheTrue HEPA1 Filterfrom _e cassetteframe. Neverattemptto cleanthe Tlue HEPA Filler.Replaoetheentire casselteonlywhenCHANGE FILTERalert t

activates.(Model85500mplacoment#85501; I

Model85501 replacement#85511) j

1.Remove the front panel and filter

NANO-SILVER!CARBON FILTER

Replacement Procedure

1,Remove the front panel by pullinggently on the sliver tabs

located on each side of the unit,

2.Pull out the filter cassette by grasp!rig tile black tabs located

on each side.

3.Remove the plasticwrap from the new filter cassette.

4.Place the new filter cassette in the main unit,

5, Replace the front panel.

cassette as described in Replacement Procedure.

2, Remove the Pro-Filter by gentlypulling one side of the cassette frame outward

while lifting the Pro-Filter tab at the same time. When one edge is clear of the frame, the Pro-Filterwill slide out for

cleanii_

3.Lightty vacuum the Pra-Fitter andwash with water and a mildhousehold deter- gent. Rinse, end shake off excess water.

4.To remove the Washable Nano-SIIverl Carbon Fitter, turn the cassette over and place facedown on an even surface. Grasp the lall white tab nearest tothe gray lab, Slightlyflex the cassette frame

outward while pulling up on the gray lab. When the first corner is released, pulloul on the olher tall frame tab while

continuingto pullup on the gray tab. When one long edge of the filter is free, slide out for cleaning,

5, Wash the filterin warm water with a mild

householddetergent, Rinse, and shake off excess water,

CASSETTE

SHORT TABS

FRONT SIDE

PowerP_g

GRAY TAB

! CASS ETT_

LONG TAB

PlasrnaDoctorTM

Display Panel

I)C Motor

Washable Nano-

SiivertCarbon F_tler

Filler Cassette with 1"rueHEPA Filter inside

-Front Panel

Remme

CanI_l

Air Outlet C_d_

TOP SIDE