Denon AVR 5700 Manual - Complete Guide for Recalling Preset Stations and Initialization

Recalling preset stations

1	Watching the display, press the SHIFT button to select the
	preset memory block.

	SHIFT	SHIFT
		SHIFT
	(Main unit)	(Remote control unit)

	2	Watching the display, press the PRESET UP or DOWN
	2	button to select the desired preset channel.
		button to select the desired preset channel.

1

2

DOWN	UP
	CHANNEL		START	LEARNED/TX	RC-853
			START	LEARNED/TX
		SYSTEM CALL		POWER
		SET	CALL	OFF	ON / SOURCE
		DVD	VDP	TUNER	SHIFT
		1	2	3
		TV/DBS	V.AUX	PHONO
		4	5	6
(Main unit)	(Remote control unit)	VCR-1	CD	MD / TAPE-1	CHANNEL
(Main unit)	(Remote control unit)	7	8	9
		7	8	9
		VCR-2		TAPE-2 MON	TV/VCR
		+10	0		A / B

1

2

VOLUME	DISC SKIP+
DOLBY / DTS

13LAST FUNCTION MEMORY

•This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off.

This function eliminates the need to perform complicated resettings when the power is switched on.

•The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit’s power switch is off and with the power cord disconnected.

14INITIALIZATION OF THE MICROPROCESSOR

When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the microprocessor is required by the following procedure.

1 Switch off the unit using the main unit’s power switch.

1,2


2	Hold the following DIRECT button and STEREO button, and
	Hold the following DIRECT button and STEREO button, and
	turn the main unit’s power switch on.

3	Check that the entire display is flashing with an interval of
	about 1 second, and release your fingers from the 2 buttons
	about 1 second, and release your fingers from the 2 buttons
	and the microprocessor will be initialized.



NOTES:			2

•If step 3 does not work, start over from step 1.

•If the microprocessor has been reset, all the button settings are reset to the default values (the values set upon shipment from the factory).

Lightly press on the button of the door to open it.

54

Image 54

Denon AVR-5700 manual Last Function Memory, Initialization of the Microprocessor, Recalling preset stations

Contents

AVR-5700 Safety Precautions Safety Instructions Table of Contents Before Using Features Connecting the audio components Connections Connecting video components Connecting a monitor TV Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting the video decks Connecting the antenna terminals AM loop antenna assemblyConnection of AM antennas Connecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jack Connecting the external input EXT. in jacks Connecting the Multi Source jacks Speaker Impedance Connecting the speaker cordsSpeaker system connections Connections Protector circuit Part Names and Functions Front Panel Remote control unit Power button …………………………36 Tuner buttons …………………………52 Surround Parameter button Setting UP the SystemSystem Setup button Enter button Surround speaker selector function Before setting up the system Setting the type of speakers System Setup Menu reappears Setting the bass outputEnter the setting At the System Setup Menu select Bass Output At the System Setup Menu select Delay Time Setting the delay timeSubwoofer Only THX recommended THX mode Front & Subwoofer Select the desired unit, meters or feet Select darken the desired units, Meters or Feet Setting the channel level Test tone A, B or A+BSurr. Sp. a Volume can be adjusted between -12 dB and +12 dB in units When the Manual mode is selectedChannel Level screen reappears Subwoofer peak limit level setting AVR-5700 automatically sets the subwoofer peak limit level Setting the digital inputs Setting the on-screen display OSD Auto tuner presets After completing system setup On-screen display signals Remote Control Unit Using the remote control unitInserting the batteries Operating Denon audio components Set mode switch 2 to the position for the component to beOperated. The tuner can be operated when the switch is at Any position but Lock Preset memory VCR VCR or TV Operating a video component stored in the preset memorySet the slide switch to the component to be registered VDP Operate the video component Learning function Using the system call function System call functionSystem call buttons Storing signals Clearing system call settings Operation Before operating Playing the input source Select the input mode Selecting the analog modeInput mode selection function Select the input source to be played Adjust the volume Select the play modeManual Auto mode Digital Auto mode Digital PCM mode Input mode when playing DTS sources After starting playback Adjusting the sound quality toneListening over headphones Turning the sound off temporarily muting Playing one source while recording another REC OUT mode Multi-source recording/playback Playback using the external input EXT. in jacks Multi-source and multi-zone playback Multi Room Music Entertainment System Adjust the level of the selected speaker SurroundBefore playing with the surround function Dolby Surround Pro Logic mode Fader function Select the Dolby Surround mode Set the input mode to Auto or RFSet the input mode to Auto or Digital DTS indicator lights when playing DTS sources LFE Low Frequency Effect Surround parameters Cinema EQ. Cinema EqualizerCOMP. Dynamic Range Compression Dialogue Normalization Home THX Cinema mode Surround modes and their features DSP Surround SimulationPersonal Memory Plus Select the surround mode for the input channel DSP surround simulationWide Screen can only be selected from the main unit Tone control setting Select Tone Surround parameters Surround modes and parameters Auto tuning Manual tuningListening to the Radio Checking the preset stations Recalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Optimum surround sound for different sources Types of multi-channel signalsAdditional Information Types of sources Movie audio Speaker setting examples Basic setting for primarily watching moviesWhen using different surround speakers for movies and music 2Dolby Digital and Dolby Pro Logic SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Digital compatible media and playback methods DTS Digital Surround Dolby Pro LogicDTS compatible media and playback methods Timber matching circuit Home THX Cinema surround modeRe-equalizer Dynamic decorrelation circuit Surround modes and parameters AUX TAPE-1 Specifications Audio section Power amplifier Rated outputPage 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan