Denon AVR-5700 manual Learning function

Learning function

•If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can “teach” the AVR-5700’s remote control to “learn” the codes from the component’s original remote control.

•The buttons that can be “learned” are the CD, DECK and MD system buttons (see page 29) and the DVD, VDP, VCR and TV system buttons (see page 32). (For the CD, MD, DVD, VDP and TV, the A block buttons can also be “learned”, and for the DVD and TV, the B block buttons can also be “learned”.)

				SET	CALL	OFF	ON / SOURCE
				DVD	VDP	TUNER	SHIFT
1				1	2	3
	Press the USE/LEARN selector button with the tip of a pen		A	TV/DBS	V.AUX	PHONO
				VCR-1	CD	MD / TAPE-1	CHANNEL
				4	5	6
	etc., to set the learn mode. Both the START and			7	8	9
	LEARNED/TX indicators flash.	Flashes		VCR-2		TAPE-2 MON	TV/VCR
				+10	0		A / B

This unit’s remote control unit

2	Set the program switch to the side to be “learned”.
	Set to the AUDIO side for the CD, tape deck or DAT position,
	to the VIDEO side for the VDP, VCR or TV position.
		AUDIO
		AVR/AVC			VIDEO
3	Set the program switch to the position to be “learned”.
		DECK	MD
	CD					LOCK
		DVD				TV
		VDP		VCR
4	Set the remote control units so they are facing each other,
	then press the button to be “learned” on this unit’s remote

control unit.

Transmitting windows	Other remote
Lit	control unit

This unit’s remote	Approx.
	5 cm
control unit

The indicator stops flashing and the START LED lights.

The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, DAT and tape deck, the buttons which can be operated with the preset memory for the VCR, VDP and TV. For the TV only, however, the buttons in the section indicated “A” on the diagram above can also be “learned”. Use these to “learn” TV channels.

4

VOLUME		DISC SKIP+
	DOLBY / DTS
HOME THX CINEMA	SURROUND	DIRECT
DSP SIMULATION	5CH STEREO	STEREO
		MASTER VOL.
INPUT MODE	ANALOG	EXT.IN

2	AUDIO		DECK	MD
			CD	LOCK	MUTING
	AVR/AVC	VIDEO	DVD	TV		3
			VDP	VCR
			SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER

		BAND	TITLE	MENU/GUIDE
				B
			CH SELECT
		MODE	ENTER
			SELECT
		MEMORY	PANEL	ON SCREEN
	1,8		DISPLAY	RETURN
		USE/LEARN T.TONE	MULTI	DVD
				SET UP
5	Check that the START LED is lit, then press the button to be
	“learned” on the other remote control unit.
				Other remote
				control unit
	This unit’s remote
	control unit
6	Once the START LED turns off and the LEARNED/TX LED
	lights, release the button on the other remote control unit.

The two LEDs start

flashing again.

Lit

7	To “learn” other buttons, repeat steps 2 to 6.
8	Once the learning operation is completed, press the
	USE/LEARN selector button again.
	The two LEDs stop flashing and the learning mode is

cancelled.

Check that the stored codes work properly.

NOTES:

•Up to 26 codes can be “learned”, but this number may be lower if the codes are long.

•If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released.

•If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-853.

•If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored.

To “learn” that code, first perform the resetting operation. (See page 36.)

33