Denon AVR-5700 manual Connections, Connecting the audio components

5 CONNECTIONS

•Do not plug in the AC cord until all connections have been completed.

•Be sure to connect the left and right channels properly (left with left, right with right).

•Insert the plugs securely. Incomplete connections will result in the generation of noise.

•Use the AC OUTLETS for audio equipment only. Do not use them for hair driers, etc.

•Note that binding pin plug cords together with AC cords or placing them near a power transformer will result in generating hum or other noise.

•Noise or humming may be generated if a connected audio equipment is used independently without turning the power of this unit on. If this happens, turn on the power of the this unit.

Connecting the audio components

• When making connections, also refer to the operating instructions of the other components.

OUTPUT		CD player	Connecting a CD player
R	L
			Connect the CD player’s analog output jacks
R	L		(ANALOG OUTPUT) to this unit’s CD jacks
			using pin plug cords.

Pre-main (integrated) amplifier for multi-source playback

Connecting a turntable

Connect the turntable’s output cord to the AVR-

Connecting the pre-out jacks

5700’s PHONO jacks, the L (left) plug to the L

Turntable

jack, the R (right) plug to the right jack.

(MM cartridge)

Use these jacks if you wish to connect external power amplifier(s) to

increase the power of the front, center and surround sound channels, or

NOTE:

for connection to powered loudspeakers. For instructions on using the

This unit cannot be used with MC cartridges

effect output, refer to page 41.

directly. Use a separate head amplifier or

Connecting the AC OUTLETS

step-up transformer.

AC OUTLETS

• SWITCHED

If humming or other noise is

(total capacity – 120 W (1 A.))

generated when the ground wire

The power to these outlets is turned on and off in conjunction with the POWER

Ground wire

switch on the main unit, and when the power is switched between on and

is connected, disconnect the

standby from the remote control unit.

ground wire.

No power is supplied from these outlets when this unit’s power is at standby.

Never connect equipment whose total capacity is above 120 W (1 A.)

NOTE:

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair driers,

Refer to page 10 for notes

TVs or other electrical appliances.

on the shorting pin plugs.

AC outlets (wall)

AC cord (included)

AC 120 V, 60 Hz

Extension jacks for future use

R

L

R

L

IN

MULTI

MONITOR

R

FRONT

R

SURROUND

FM

PHONO

SOURCE

L

A

L

OUT-1

COAX.

R

L

OUT

Y

CB

CR

Y

CB

CR

Y

CB

CR

75

MONITOR

IN

DVD

IN

TV/DBS

MONITOR

OUT

SIGNAL CD

FRONT

OUT-2

COMPONENT VIDEO

GND

CENTER

LOOP

DVD

SUB

DVD

ROOM TO ROOM

ANT.

WOOFER

AM

REMOTE

IN

IN

CONTROL

R

VDP

SURROUND

VDP

OUT

ANTENNA TERMINALS

TV/

TV/

SPEAKER

EFECT

IMPEDANCE

DBS

DBS

FRONT,CENTER /6

16

CENTER

PREOUT

R

L

SURROUND /

16

V.AUX

V.AUX

A OR B

6

SPEAKER SYSTEMS

A+B

12

16

6CH EXT. IN

OUT

R

L

FR

FL VCR-1

VCR-1

VCR-1

R

B

L

SURROUND

SW

C

VCR-2

VCR-2

R

L

VCR-2

DOLBY DIGITAL

OPTICAL

OPTICAL-5

R

COAXIAL

AC IN

SL MD/

MD/

OUT

IN

RF

1

2

3

4

IN

OUT

IN

SR

VCR-1

1

2

3

L

TAPE-1

TAPE-1

SWITCHED TOTAL 120W(1A.) MAX.

ER

EL TAPE-2

TAPE-2

VCR-2

AC 120V

60Hz

8CH EXT. IN

R

L

AUDIO

R

VIDEO

S-VIDEO

DIGITAL

AC OUTLETS

L

Route the connection cords, etc., in such a way that

they do not obstruct the ventilation holes.

R

L

R

Tape deck 2

MD player, DAT deck or other component

L

equipped with digital input/output jacks

R L	R L
OUTPUT	INPUT	OUTPUT INPUT
Connecting a tape deck		OPTICAL

Connections for recording:					CD player or other component
Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s					equipped with digital output jacks
tape recording (OUT) jacks using pin plug cords.					OPTICAL COAXIAL
					OUTPUT
Connections for playback:
Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s					Connecting the DIGITAL jacks
tape playback (IN) jacks using pin plug cords.
					Use these for connections to audio equipment with digital output.
OUTPUT		INPUT		Tape deck 1 or MD	Refer to page 25 for instructions on setting this terminal.
R	L	R	L
					NOTES:
R	L	R	L		• Use 75 Ω /ohms cable pin cords for coaxial connections.
					• Use optical cables for optical connections, removing the cap
					before connecting.

6