Kenwood FP580, FP480 manual safety, key processor, liquidiser, additional attachments

before using your Kenwood appliance

●Read these instructions carefully and retain for future reference.

●Remove all packaging and any labels.

safety

● The blades and discs are very sharp, handle with care.	￿a
Always hold the knife blade by the finger grip
￿a at the top, away from the cutting edge, both
when handling and cleaning.

●Always remove the knife blade before pouring contents from the bowl.

●Keep hands and utensils out of the processor bowl and liquidiser jug whilst connected to the power supply.

●Switch off and unplug:

●before fitting or removing parts

●after use

●before cleaning

●Never use your fingers to push food down the feed tube. Always us e the pusher/s supplied.

●Before removing the lid from the bowl or liquidiser/mill from the power unit:-

●switch off;

●wait until the attachment/blades have completely stopped;

●Be careful not to unscrew the liquidiser jug or mill from the blade unit.

●Liquids should be allowed to cool to room temperature before blending.

●Do not use the lid to operate the processor, always use the on/off speed control.

●This machine will be damaged and may cause injury if the interlock mechanism is subjected to excessive force.

●Never use an unauthorised attachment.

●Never leave the machine on unattended.

●Never use a damaged machine. Get it checked or repaired: see ‘service’.

●Never let the power unit, cord or plug get wet.

●Don’t let excess cord hang over the edge of a table or worktop or touch hot surfaces.

●This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

●Children should be supervised to ensure that they do not play with t he appliance.

●Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

●Misuse of your processor/liquidiser can result in injury. before plugging in

●Make sure your electricity supply is the same as the one shown on th e underside of your machine.

Important – UK only

●The wires in the cord are coloured as follows: Blue = Neutral, Brown = Live.

●The appliance must be protected by a 3A approved (BS1362) fuse.

Note:

●For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).

●If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.

●This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.

before using for the first time

1Remove all packaging including the plastic blade covers from the kni fe blade.

Take care the blades are very sharp. These covers should be discarded as they are to protect the blade during manufacture and transit only.

2Wash the parts see ‘cleaning’

3Push excess cord into the back of the machine.

key

processor

￿power unit

￿detachable drive shaft

￿bowl

￿lid

￿feed tube

￿pushers

￿safety interlock

￿cord storage

￿pulse control

￿speed control

liquidiser

￿filler cap

￿lid

￿jug

￿sealing ring

￿blade unit

additional attachments

Not all of these attachments listed below will be included with your food processor. Please refer to your content list supplied. To buy an attachment not included in your pack, contact the dealer from whom you purchased your appliance.

￿knife blade

￿dough tool

￿twin beater geared whisk

￿maxi-blend canopy

￿thick slicing/coarse shredding disc ￿21 thin slicing/fine shredding disc

￿22 fine (Julienne style) chipper disc ￿23 rasping disc (if supplied)

￿24 geared citrus press (if supplied) ￿25 mill (if supplied)

to use your food processor

1Fit the detachable shaft onto the power unit ￿.

2Then fit the bowl. Place the handle towards the back and turn clockwise until it locks ￿.

3Fit an attachment over the drive shaft.

●Always fit the bowl and attachment onto the machine before adding ingredients.

4 Fit the lid ￿ - ensuring the top of the drive shaft locates into the centre of the lid.

●Do not use the lid to operate the processor, always use the on/off

speed control.

5 Switch on and select a speed.

●The processor won’t work if the bowl and lid are fitted incorrectly.

●Use the pulse control for short bursts. The pulse will operate for as long as the lever is held down.

6Reverse the above procedure to remove the lid, attachments and bowl.

● Always switch off before removing the lid.

important

●Your processor is not suitable for crushing or grinding coffee beans, or converting granulated sugar to caster sugar.

●When adding almond essence or flavouring to mixtures avoid contact with the plastic as this may result in permanent marking.

2