Kenwood HM-331 Selection of reverse mode (Main unit only), Selection of TAPE equalizer (tape EQ.), Tape counter display, To wind tape at high speed (remote control only)

To wind tape at high speed (remote control only)

To fast wind in	To fast wind in
direction 1	¡ direction \

÷Press the 7key to stop fast winding.

Let's put out some sound 19

HM-331 (En/T)

To stop playback

STOP

7

÷Do not take out the cassette tape until the tape transport has stopped completely.

Selection of reverse mode (Main unit only)

1Select “TAPE RVS. ?”.

Selection of TAPE equalizer (tape EQ.)

(Main unit only)

menu

VOLUME / multi control

When playing a tape prerecorded with Noise Reduction system (such as the DOLBY NR) ON, be sure to set the "tape EQ." ON for playback.

tape	Lit when “tape EQ.” is ON
EQ	T.E.

Each press switches the modes as follows.

1 “tape EQ.” ON......... TAPE equalizer is used.

2“tape EQ.” OFF ....... TAPEequalizerisnotused.

÷Select the "tape EQ." ON mode according to the recording condition of the tape.

				Lights
RANDOM PGM REPEAT		ALL SLEEP A.P.S. O.T.T. PROG. 1		2 R·D·S EON EON
	TRACK NO.	TOTAL AUTO TUNED	STEREO		TP TA PTY
FM	8 8 8 8 0 0 0 0
AM			kHz
				O.T.E.		NR T.E.
PM			MHz

T A P E • •S T O P •TITLE SEARCH

MD EDIT

÷Normal (TYPE ), high (TYPE ), or metal (TYPE ) tape selection is set automatically.

÷Remove tape slack before loading.

÷Close the door securely.

Displayed when the deck is loaded with a tape.

RANDOM PGM		REPEAT ALL SLEEP A.P.S. O.T.T. PROG. 1		2 R·D·S EON EON
	TRACK NO.	TOTAL AUTO TUNED	STEREO		TP TA PTY
FM	8 8 8 8 0 1 5 2
AM			kHz
				O.T.E.		NR T.E.
PM			MHz

T A P E • •P L A Y •TITLE SEARCH

MD EDIT

Reverse mode indication

set/demo

(Press the “set/demo” key while the “?” mark is blinking.)

2Select.

Initial setup

“” : (REVERSE)

Both sides are played back (recorded), and then the tape stops.

VOLUME / multi control		“ ”:
“ ”: (ONE-WAY)
Only one side is		(ENDLESS)
played back (re-		Both sides are	Basic
the tape stops.
corded), and then		played back
do	u	endlessly.	section
wn
	p	(The tape stops
		after recording
3Set it.		onto both sides.)
set/demo

Tape counter display (Remote control unit only)

Each press of the TIME DISP. key changes the displayed contents.

1 AM	0 0 0 0	(Tape count)
2 AM	8 4 5	(Time display)

A tip for use of the tape counter

The tape counter is set to “0000” when a cassette tape is loaded.

By writing down the counter reading in case you want to interrupt recording (playback) in the middle of the tape, the memo will be helpful as a reference for locating the same position when continuing the recording (playback) the next time. The tape counter figure decrements during recording or playback of the back side (while the 2

tape transport indicator is lit).
To set the tape counter	FM	TRACK NO.TOTAL AUTO TUNED	STEREO
		8 8 8 8 0 0 0 0
to “0000”, open the cas-	AM		kHz
	PM		MHz
sette holder once.	T A P E • •S T O P
Then the counter will be
reset.