Kenwood HM-335 In case of difficulty

Important Items

45 EN

In case of difficulty

What seems to be a malfunction is not always so. Before calling for service, check the following table

according to the symptom of your trouble.

Operation to reset

The microcomputer may fall into malfunction (impossi-

bility to operate, erroneous display, etc.) when the

power cord is unplugged while unit is ON or due to an

external factor. In this case, execute the following pro-

cedure to reset the microcomputer and return it to nor-

mal condition.

Unplug the power cord from the power outlet, then

while holding the POWER or key depressed, plug

the power cord again.

÷Please note that resetting the microcomputer

clears the contents stored in and it returns to condi-

tion when it left the factory.

or

After resetting the microcomputer, the display will show

as follow:

standby/timer

POWER

standby/timer

Sound is not produced.

The "standby/timer" indicator blinks in red and

no sound is output.

The "standby/timer" indicator blinks in green.

No sound from the headphones.

Sound is not produced from the left or right

speakers.

The clock display blinks without changing the

figures.

Timer operation is not possible.

÷Connect properly referring to "System connections". 6

÷Adjust to a required volume. $

÷Switch MUTE OFF. %

÷Unplug the headphone plug.

÷A speaker cord is short-circuited. Turn power off and re-connect

the speaker cord.

÷Adjust the present time again. ‡

÷Set the timer ON/OFF time properly ‚

÷Insert correctly. %

÷Adjust to a required volume. $

÷Connect properly referring to "System connections". 6

÷Adjust the present time again. ‡

÷Adjust the present time referring to "Clock adjustment". ‡

÷Set the timer ON time and OFF time. ‚

÷Connect antennas. 78

÷Select a band. )

÷Tune to the frequency of the desired station. )

÷Install the outdoor antenna in an apart position from the road.

÷Switch the suspected electric appliance OFF.

÷Install the TV or the system at an increased distance between

them.

÷Preset stations with tunable frequencies. ¡

÷Preset stations again. ¡

Radio stations cannot be received.

Noise interferes.

A station has been preset but it cannot be re-

ceived by pressing the P.CALL key.

RemedySymptom

RemedySymptom

Amplifier section/Speakers

Tuner section

Contents

Main MICRO HI-FI COMPONENT SYSTEM INSTRUCTION MANUAL KENWOOD CORPORATION HM-335 For the United Kingdom Factory fitted moulded mains plug The marking of products using lasers Safety precautions Before applying power Caution : Read this page carefully to ensure safe operation. * AC voltage selection (For countries other than U.S.A., U.S.-Military and Canada) VOLTAGE SELECTOR 110V/220V Special features Playback capability of CD-R and CD-RW discs. Accessories Unpacking Keep this manual handy for future reference. CAUTION FCC WARNING Contents Preparation section Basic section Application section Knowledge sections System connection This figure shows the method of connection between the main unit and provided accessories. AM loop antenna AM loop antenna How to connect speaker cords to the main unit FM indoor antenna How to connect AM antenna cord to the main unit Speaker cord FM indoor antenna Connection of Other Accessories CAUTION POWER cord FM outdoor antenna Controls and indicators AUTO POWER SAVE function Display ! 5687 Main unit About the one-touch operation function Standby mode Top view Front view 1 2 3 4 5 6 7 Operation of remote control unit Operation Loading batteries 1 Remove the cover. 2 Insert batteries. 3 6 7 Basic use method Set the key (or POWER key) to ON. Pressing the key (or POWER key) when the unit is ON turns it off (Standby mode of power). Selecting the desired output. CD ^ TAPE * TUNER (Broadcasts) ) AUX (External input) [Adjusting the AUX input level ] Muting the sound temporarily Enhancement of bass 2 Listening through headphone Tone adjustment Playback of CD 1 open to open the CD lid. 2 3 open to close the CD lid. Start playback/ To pause playback To fast forward and backward To select track No. 30 : Skipping tracks Playback from desired track Playback of TAPE 1 2 3 To wind tape at high speed Selection of TAPE equalizer (TAPE EQ.) A tip for use of the tape counter To stop playback Selection of reverse mode Receiving broadcast station Receiving broadcast station 1 2 Collective presetting of stations Channel space setting 1 2 One-by-one presetting 1 4 2 Tuning to a non-preset radio station RDS (Radio Data System) Before using RDS RDS (Radio Data System) Set the reception band to FM. Preset RDS stations with the auto memory function. Program Type Name Display Searching for a desired program type RDS (Radio Data System) Start the search. To change to a different program type : Repeat steps 1, 2, 3. Recording on TAPE Load a tape in deck. Recording on TAPE 1 2 3 Recording on TAPE Select the reverse mode. ( Start recording. Select the source to be recorded. Stop the recording 4. 5. Points in CD recording Select "PGM" mode. Select track numbers in the order you want to play them. Start playback. 1 To select track No. 30 : Various CD playback features Listening to the desired sequence Use the following procedure to program desired tracks in a desired order. (up to 32 tracks) (program playback) To add a track to an existing program 1 To select track No. 30 : To clear the entire program the numeric keys. Repeated playback Setup for repeating selected tracks Playing tracks in a random order 1 2 2 3 To stop repeated playback Convenient recording methods All-track recording Single-track recording One-touch edit recording = Make preparation for recording. Select the desired CD track and play it.If it is in play mode, stop it. Be sure to put the cassette deck in stop mode. Program recording = (CD Desired CD tracks can be programed in the desired sequence and recorded onto a tape. Make preparation for recording. Listening to an AUX input source Select AUX (external input). Play the connected equipment. Adjust the volume. 4 Adjusting the AUX Input Level 1 2 Clock adjustment Adjust the hour. 1 Activate the Clock adjustment mode. Adjust the minute. Timer operation AI timer playback (PROG 1, PROG 2) Timer playback, timer recording (PROG 1, PROG 2) Sleep timer (SLEEP) Sleep timer (SLEEP) Setting the timer program (PROG. TIMER) Connect the related equipment under reference to "System connection" Adjust the clock before setting the timer Make preparations for the play (recording). Select the program timer ON/OFF. 1 Select ONETIME or EVERYDAY execution of the programed timer. 1 Set the ON time then the OFF time. Make the desired reservation. 1 For timer playback or AI timer playback For timer recording 2 3 Put the unit in standby mode. Important Items Note related to transportation and movement Maintenance Reference Maintenance of the unit Disc handling precautions Handling Cleaning To store cassette tapes Safety tab (accidental erasure prevention tab) In case of difficulty Operation to reset Tuner section Amplifier section/Speakers CD player section In case of difficulty Cassette deck section Remote control unit Displayed messages and actions to be taken against them In case of difficulty Note to CATV system installer Specifications [Amplifier section] [Tuner section] [CD player section] Main unit