Connection

* Commercially available parts

2WARNING

To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal.

2 CAUTION

• If sound is not output normally, immediately

turn power off and check connections.

• Be sure to turn the power off before changing

the setting of any switch.

• If the fuse blows, check wires for shorts, then

replace the fuse with one of the same rating.

• Check that no unconnected wires or connectors

CENTER UNIT (CD receiver, etc.)

RCA cable*

Lead terminal*

Left input

Power control wire

Right input

are touching the car body. Do not remove

caps from unconnected wires or connectors to

prevent short circuits.

• Connect the speaker wires to appropriate

speaker connectors separately. Sharing the

negative wire of the speaker or grounding

speaker wires to the metal body of the car can

cause this unit to fail.

• After installation, check that the brake lamps,

winkers, and wipers work properly.

30

30

4

3

2

1

Terminal cover

Battery wire*

Protective Fuse*

5

6

 

7

 

8

0

9

GND

RCA cable ground terminal

Right speaker

Left speaker

Bridged Connections

Speaker (Bridged)

Battery

Ground wire*

LX-Bus connection

 

 

To Kenwood disc changer/

CENTER UNIT

External optional accessory

 

 

 

 

 

 

 

 

 

 

 

Control cable

 

Power control wire

(option)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

5

6

 

 

 

 

 

 

 

 

3

 

7

 

 

 

 

 

 

 

 

2

 

8

 

 

 

 

 

 

 

 

1

09

 

 

 

Master amplifier

"0"

 

4

5

67

 

 

 

 

3

 

 

 

8

 

 

 

 

2

 

 

 

 

 

 

 

1

0

9

 

 

 

 

 

 

ID NUMBER

 

 

 

S-video cable*

RCA cable*

Extension wire*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

5

6

 

 

 

 

 

 

 

 

3

 

7

 

 

 

 

 

 

 

 

2

 

8

 

 

 

 

 

 

 

 

1

0

9

 

 

 

Slave amplifier 1

"1" –

 

 

4

5

6

 

 

 

 

7

 

 

 

 

3

 

 

 

9 8

 

 

 

 

2

 

 

 

 

"7"

 

 

 

 

1

0

 

 

 

 

ID NUMBER

 

 

 

 

 

 

 

 

 

 

 

Not more than

 

 

 

 

 

 

 

 

 

 

14m (46 ft)

30

30

 

 

 

4

5

6

 

3

 

7

 

2

 

8

 

1

0

9

Slave amplifier 7

 

3

5

7

 

"1" – "7"

4

 

6

 

2

0

8

 

 

1

 

9

ID NUMBER

Set the ID number of the Master amplifier to "0".

You can connect up to 7 Slave amplifiers. Assign them ID numbers "1" to "7" and do not duplicate them.

2CAUTION

Do not connect 2 Master amplifiers to the Center Unit. If done, you cannot control all amplifiers connected to the Center Unit.

The LX AMP and the sensor unit cannot be connected simultaneously. You must connect any of them at a time.

NOTE

The total length of S-video cables you can connect is 14 meters (46 ft) maximum. If the cable length exceeds this limit, you cannot control amps from the Center Unit.

If you assign the same ID number to multiple amplifiers, they malfunction when you operate any of them from the Center Unit.

If you assign ID number "8" or "9" to a Slave amplifier, it is not recognized by the Center Unit.

4English