Connection
* Commercially available parts
2WARNING
To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal.
2CAUTION
•If sound is not output normally, immediately turn power off and check connections.
•Be sure to turn the power off before changing the setting of any switch.
•If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.
•Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits.
•Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.
•After installation, check that the brake lamps, winkers, and wipers work properly.
CENTER UNIT (CD receiver, etc.)
RCA cable ground terminal
|
|
| RCA cable* |
Power control wire |
|
| |
| GND |
| Left input |
|
|
| |
30 | 30 |
|
|
| 4 | 5 | 6 |
| 3 |
| 7 |
| 2 |
| 8 |
| 1 | 0 | 9 |
|
|
| Right input |
Terminal cover |
|
| Lead terminal* |
|
|
| |
Battery wire* |
|
|
|
Protective Fuse* |
|
| Subwoofer (L + R) |
Battery | Ground wire* |
■LX-Bus connection
CENTER UNIT
Power control wire
To Kenwood disc changer/ External optional accessory
Control cable (option)
Set the ID number of the Master amplifier to "0".
You can connect up to 7 Slave amplifiers. Assign them ID numbers "1" to "7" and do not duplicate them.
2CAUTION
•Do not connect 2 Master amplifiers to the Center Unit. If done, you cannot control all amplifiers connected to the Center Unit.
•The LX AMP and the sensor unit cannot be connected simultaneously. You must connect any of them at a time.
NOTE
30 | 30 |
|
|
|
| 4 | 5 | 6 |
|
| 3 |
| 7 | |
| 2 |
|
| 8 |
| 1 | 0 | 9 |
|
Master amplifier |
| "0" | 3 | 5 |
| 7 |
|
|
| |
|
| 4 |
| 6 |
|
|
|
| ||
|
| 1 | 0 | 9 |
|
|
| |||
|
|
| 2 |
|
|
| 8 |
|
|
|
|
|
| ID NUMBER |
|
| |||||
Extension wire* |
|
|
|
|
|
|
|
| RCA cable* | |
30 | 30 |
|
|
|
|
|
|
|
|
|
|
|
|
| 3 | 4 | 5 | 6 |
|
|
|
|
|
|
|
|
| 7 |
|
|
| |
|
|
|
| 2 |
| 8 |
|
|
| |
|
| "1" – |
| 1 | 0 | 9 |
|
|
| |
Slave amplifier 1 |
|
| 2 | 5 | 9 | 8 | ||||
|
|
|
| 3 |
| 7 | ||||
|
|
|
|
|
| 4 |
| 6 |
| |
|
| "7" |
|
|
|
| 1 | 0 |
|
|
|
| ID NUMBER | ||||||||
|
|
|
|
|
|
|
|
|
| Not more than |
|
|
|
|
|
|
|
|
|
| 14m (46 ft) |
30 | 30 |
|
|
|
| 4 | 5 | 6 |
|
| 3 |
| 7 | |
| 2 |
|
| 8 |
| 1 | 0 | 9 |
|
Slave amplifier 7 | "1" – "7" | 3 | 5 | 6 |
| 4 | 0 | ||
|
| 7 | ||
|
| 2 |
| 8 |
|
| 1 |
| 9 |
ID NUMBER
•The total length of
•If you assign the same ID number to multiple amplifiers, they malfunction when you operate any of them from the Center Unit.
•If you assign ID number "8" or "9" to a Slave amplifier, it is not recognized by the Center Unit.
4English