turning on the power with AUX source selected.

Turn off the attenuator function when listening to output from external unit. This prevents the noise when no external unit is connected to AUX terminal.

OFF: Disables the selection of AUX source.

Set to OFF when not using the AUX terminal.

ÍCD READ: “CD READ” ➤ “1”*, ”2” Sets the method for reading CD.

When unable to play special format CD, set this function to “2” to force playing. Note that some music CD may be unplayable even when set to “2”.

In addition, audio files cannot be played when set to “2”. Normally, keep this set to “1”.

1: Automatically distinguishes between audio file disc and music CD when playing disc.

2: Forces playing as music CD.

ÎSwitching Preout: “SWITCH PRE” ➤ “REAR”*,”SUB-W”

Switches the preout between rear output (“REAR”) and subwoofer output (“SUB-W”).

ÏSpeaker Select: “SP SELECT” ➤ “OFF”*, ”5/4”, ”6*9/6”, ”OEM”

Fine-tuning so that the System Q value is optimal when setting the speaker type as follows;

Speaker type

 

Display

OFF

 

 

“SP OFF”

For 5

& 4 in. speaker

 

“SP 5/4”

For 6

& 6x9 in. speaker

 

“SP 6*9/6”

For the OEM speaker

 

“SP OEM”

ÌFirmware Upgrade: “F/W UP xx.xx” Upgrades the firmware.

Selecting “YES” and then pressing [VOL] knob starts upgrading the firmware.

⁄

•For how to update the firmware, access our web site. http://www.kenwood.com/cs/ce/

<DEMO MODE>

ÓDemo Mode: “DEMO MODE” ➤ “ON”*, ”OFF” Specifies whether to enable demonstration.

<AUDIO CONTROL>ÔSubwoofer output: “SUB-W SET” ➤ “ON”*, ”OFF”

⁄

•This setting can be made when “SUB-W” is selected for the <Switching Preout> item.

Bass Boost: “BASS BOOST” ➤ “LV1”*, ”LV2”, ”OFF” Ò System Q: “SYSTEM Q” ➤ “NATURAL”*, ”ROCK”,

”POPS”, ”EASY”, ”TOP 40”, ”JAZZ”, ”GAME”, ”USER” Switches between the following preset equalizer curves;

Natural, Rock, Pops, Easy, Top 40, Jazz, Game, User setting

⁄

•“USER”: This appears when Bass level, Middle level, and Treble level are adjusted. When the System Q setting is changed, the Bass, Middle, and Treble set replace the System Q values.

ÚBass level adjust: “BASS LEVEL” ➤ “-8” – ”+ 8” " Middle level adjust: “MID LEVEL” ➤ “-8” – ”+ 8” Æ Treble level adjust: “TRE LEVEL” ➤ “-8” – ”+ 8”

⁄

•Ú - Æ : Source tone memory: Puts the set up value in the memory per source.

åBalance: “BALANCE” ➤ “L 15” – ”R 15”ßFader: “FADER” ➤ “R 15” – ”F 15”∂Subwoofer level adjust: “SUB-W LEVEL” ➤ “- 15” – ”+ 15”

ƒSubwoofer Low Pass Filter: “LPF SUB-W” ➤ “85”, ”120”, ”160”, ”THROUGH”(OFF)*

©Subwoofer Phase: “SUB-W PHASE” ➤ “REV”(180°), ”NORM”(0°)*

⁄

•∂ - © : These adjustments can be made when “ON” is selected for the <Subwoofer output> item.

•© : This adjustment can be made when a setting other than “THROUGH” is selected for the <Subwoofer Low Pass Filter> item.

˙Supreme: “SUPREME SET” ➤ “ON”*, ”OFF” Technology to extrapolate and supplement with proprietary algorithm, the high-frequency range that is cut off when encoding at low bit rate (less than 128Kbps, Sampling frequency is 44.1kHz). Supplementing is optimized by compression format (MP3 or WMA) and processed according to bit rate.

The effect is negligible with music that is encoded at high bit rate, variable bit rate or has minimal high frequency range.

Can be set while Audio file source of CD. Volume offset: “VOL OFFSET” ➤ “- 8” – ”±0” (When in AUX source: ”-8” – ”+8”)

Sets each source’s volume as a difference from the basic volume.

English 9