Connecting the system control
Setting up the system
1 1
Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown below.
ƒMode : lets you combine f, ƒ, and F terminals 
Mode : for 
terminals only
This unit is compatible with both [XS8] and [SL16] modes. It comes from the factory set to the [SL16] mode. To switch to the [XS8] mode, follow the instructions in “SWITCHING FROM [SL16] TO [XS8]” below.
Preparations
EXAMPLE: [XS8] mode connections
The underlined portion represents the setting of the system control mode.
[SL16] [XS8] | Receiver |
|
|
|
|
|
|
[SL16] | MD recorder |
|
|
|
|
| SYSTEM |
|
|
| |
[SL16] [XS] [XS8] [XR] | Cassette deck |
| |
| |||
| CONTROL | ||
| |||
[SL16] [XS] [XS8] |
|
| cord |
CD player |
|
| |
|
| ||
|
|
|
|
|
|
|
|
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system control mode.
[SL16] [XS8] | Receiver |
|
|
|
|
|
|
|
|
|
|
[SL16] | MD recorder |
| SYSTEM |
| |||
[SL16] [XS] [XS8] [XR] |
|
| |
|
| ||
Cassette deck |
| ||
| |||
| CONTROL | ||
| |||
[SL16] [XS] [XS8] |
|
| cord |
CD player |
|
| |
|
| ||
|
|
|
|
[XS] | Record player | [XS] | Record player |
•In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must be connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the TAPE/MD jacks. When using more than one CD player (etc.) only the one connected to the specified jacks may be connected for system control.
•Some CD players and cassette decks are not compatible with the [SL16] system control mode. Be sure to use the [XS8] system control mode when making system connections with equipment that is not [SL16] compatible.
•Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.
1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your equipment consists of this kind of combination, please do not connect any system control cords. Even without
Notes
system control cords, normal operations can be carried out without effecting performance.
2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
SYSTEM CONTROL OPERATIONS
Remote Control
Lets you operate this unit with the system remote supplied with the receiver.
Automatic Operation (except [XR] equipment)
When you start playback from a source component, the input selector on this unit switches to that component automatically.
Synchronized Recording (except [XR] equipment)
Lets you synchronize recording with the start of playback when recording from CD, MD or analog discs.
SWITCHING FROM [SL16] TO [XS8]
You can easily change the system control mode by adjusting the position of the SYSTEM CONTROL switch on the rear panel.
Do this operation after completing all connections.
For [SL16] SL 16 XS 8 For [XS8]
•This operation will not effect items stored in the memory.
•After switching the system control mode, turn the power off and then on once to confirm the new setting.
Registering setup codes for KENWOOD audio components
• Once you finish making the system connections, be sure to register the appropriate setup code for each component. | fi |
•If you own remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your other system control components), registering the setup code enables you to control those components using the remote control supplied with this unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see
"Registering setup codes for other components". | fi |