Listening to a source component

VOLUME CONTROL

INPUT SELECTOR

VIDEO AUDIOVOLUME

VOLUME

Input selector keys

RC-R0508

RC-R0710

1Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)) to select the source you want to listen to.

The input sources change as shown below:Selecting a source using the INPUT SELECTOR knob1 TUNER2"CD" ("CD"*)3"TAPE" or "MD" ("TAPE"*)4 "PHONO"("PHONO"*)5 "VIDEO1" ("VCR1"*)6 "VIDEO2" ("VCR2"*)7 "DVD 6ch"Selecting a source using the AUDIO key on the remote control (RC-R0508)1 "CD" ("CD"*)2"TAPE" or "MD" ("TAPE"*)3 TUNER

4 "PHONO"("PHONO"*)

Selecting a source using the VIDEO key on the remote control (RC-R0508)1 "VIDEO1" ("VCR1"*)2"VIDEO2" ("VCR2"*) 3 "DVD 6ch"

•When selecting an input source by using the remote control (RC- R0710), press the desired input selector key.

•“VIDEO 2” can be selected as an input source only if the VIDEO 2/

MONITOR setting is “VIDEO 2” .

8

*Once setup codes are registered in the remote control (RC-R0508), the input name display changes according to the name of the

registered component.

Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears

instead of "VIDEO 1".

RC2

•When using the remote control (RC-R0508) after initial setup, any inputs that have not been registered with a setup code are deleted

from the cyclic list.

RC4

•The INPUT SELECTOR on the front panel of the receiver always cycles through all inputs.

2Start playback from the selected source.

 

 

 

 

 

 

 

 

 

 

Normal playback

 

 

 

 

 

 

 

 

 

 

KRF-V7020/V6020/V5020 (En/T)

Adjusting the sound

 

 

 

15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOURCE DIRECT

VOLUME CONTROL

 

BASS BOOST

SOUND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PHONES

MULTI CONTROL

 

SPEAKERS A/B

 

SPEAKERS, MUTE (KRF-V5020)

 

VIDEO

 

 

VOLUME

VOLUME

 

MUTE

 

TUNING/SKIP

 

SOUND

 

MUTE

 

MULTI CONTROL

 

 

 

SOUND

 

 

RC-R0508

RC-R0710

 

Adjusting the tone

 

Operations

The following adjustments are possible if the receiver is in the stereo

 

mode.

1Press the SOUND key to select the tone mode to be adjusted.

BASS: Select this to adjust the low frequency range. (Press the SOUND key once.)

TREB: Select this to adjust the high frequency range. (Press the SOUND key twice.)

SP A

L

R

TREB+4 STEREO

 

 

SW

 

2Use the MULTI CONTROL (TUNING/SKIP) to adjust the sound quality.

•The bass and treble levels are adjustable from -10 to +10 in 2 step increments.

•The adjustment item is displayed for approximately 8 seconds.

•If you used the remote control (RC-R0508) to perform the above setting, press the VIDEO key at this point to turn off the remote control’s own adjustment mode. In this case, the input source is not switched.

Once-touch low frequency emphasis (bass boost)

The following adjustments are possible if the receiver is in the stereo mode.

Press the BASS BOOST key.

•Press the key once to select the maximum (+10) low frequency emphasis setting.

•This key does not function when the receiver is in the sound quality or ambience effects mode.

Switching back to the previous settingPress the BASS BOOST key again.
3Use the VOLUME CONTROL (VOLUME) to adjust the volume.