| Setting up the system | |
8 | Make connections as shown below. | |
When connecting the related system components, be sure to also refer | ||
to the instruction manuals supplied with the components you are | ||
| ||
| connecting. | |
| Do not connect the power cord to a wall outlet until all connections are |
Connecting audio components
Shape of AC outlets
|
| completed. |
|
|
|
|
| DTS disclaimer clause |
|
| DTS Digital Surround™ is a discrete 5.1 channel digital audio format |
|
| available on CD, LD, and DVD software which consequently cannot be |
Preparations |
| decoded and played back inside most CD, LD, or DVD players. For this |
| reason, when | |
| outputs of the CD, LD, or DVD player, excessive noise will be exhibited. | |
| To avoid possible damage to the audio system, proper precautions | |
| should taken by the consumer if the analog outputs are connected | |
| directly to an amplification system. To enjoy DTS Digital Surround™ | |
|
| |
|
| playback, an external 5.1 channel DTS Digital Surround™ decoder |
|
| system must be connected to the digital output (S/P DIF, AES/EBU, or |
|
| TosLink) of the CD, LD or DVD player. |
|
| The only audio product model incorporating the DTS Digital Surround |
|
| decoder is the |
|
|
|
SYSTEM CONTROL jacks @
U. K.
Other countries
To AC wall outlet
VIDEO 2/MONITOR jacks (for |
The receiver’s VIDEO 2/MONITOR jacks can be used in two different |
ways. Make the appropriate setting for the component connected to the |
jack when the receiver is turned on. |
Use as a VIDEO 2 jack |
You can connect a video deck or the like to these jacks and perform |
video playback and recording. The initial factory setting is “VIDEO 2ﾓ. |
Use as a MONITOR jack |
You can connect a cassette deck or the like to these jacks and make use |
of the deck’s monitoring function during recording. Alternately, you can |
connect a graphic equalizer to these jacks to apply compensation to the |
music signal. |
L |
|
|
|
|
R |
|
|
|
|
GND | REC OUT | PLAY IN | REC OUT | PLAY IN |
| ||||
PHONO | CD/DVD | MD/TAPE1 |
| MONITOR |
|
|
|
| AUDIO |
VIDEO2/MONITOR jacks
You can connect an equalizer in Monitor mode, or a video component in Video 2 mode.
To use the VIDEO 2/MONITOR jacks as MONITOR jacks, hold down |
the MONITOR key of the main unit for more two seconds so that the |
indication shown below appears. |
MONITOR |
|
|
|
|
|
|
|
|
|
|
|
| FM | AUTO SOUND | DIGITAL |
| AUTO |
|
| SP |
| A |
| B |
| TI.VOL | L | C |
| R | AM | PRO LOGIC | S.DIRECT |
| MEMO |
|
| CLIP |
|
|
|
|
| MUTE | LFE |
| SW |
|
|
| ||||
|
|
|
|
|
|
|
| MHz | 3 STEREO | MONITOR |
| ST. |
| ||||
| RDS | EON | PTY |
|
|
|
|
| |||||||||
|
| LS | S | RS |
| kHz | DOWN MIX | DSP | TUNED |
| |||||||
| TP | TA |
| NEWS |
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•At the same time the setting is switched to “MONITOR,” the audio input source switches to tuner and the video input source switches to VIDEO 1.
•To switch the setting back to “VIDEO 2,” once again hold down the MONITOR key for two seconds or more.
Notes
1.Be sure to insert all connection cords securely. If their connections are imperfect, the sound may not be produced or noise may interfere.
2.Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging/unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit.
3.Do not connect power cords from components whose power consump- tion is larger than what is indicated on the AC outlet at the rear of this unit.
Analog connections
Audio connections are made using RCA pin cords. These cables transfer stereo audio signal in an “analog” form. This means the audio signal corresponds to the actual audio of two channels. These cables usually have 2 plugs each end, one red for the right channel and one white for the left channel. These cables are usually packaged with the source unit, or are available at your local electronics retailer.
IN | OUT |
|
Video component, |
| |
3 head cassette deck, or |
| |
Graphic equalizer | * | |
|
|
|
OUT
Cassette deck or
MD recorder
IN
OUT
CD player
OUT
Record player
When you connect the video component to the VIDEO2/MONITOR jacks, connect the video cord (yellow RCA pin cords) of the connected component to the VIDEO2 IN jack